1970

16" X 3.0" front or rear wheel assembly includes black hub, chrome rim and 40 zicad plated spokes.*NOTE: Zicad is a dull shade of zinc similar to cadmium. This wheel assembly also...

V-Twin - 52-0300 - 16 inch x 3 inch Wheel Rim and Spoke Kit Chrome SteelDescriptionRim and spoke set include 16" x 3" front rim with 40 chrome spokes with 40 spoke nipples.For use with a steel hub...

16" x 3.00 rear wheel assembly with chrome hub and bearings installed, chrome rim, and chrome spokes.*NOTE: The valve stem hole is on the sprocket side. **NOTE: All spokes on wheel need to be...

H-C type 2.15" x 19" alloy rim features a polished natural finish and has 40 spoke holes.Exact as original! Rim is drilled to fit Harley type applications on smaller diameter hubs. CV hole measures...

H-C type 2.15 x 18" alloy wheel rim features a polished natural finish and has 40 spoke holes.Exact as original! Outside measurement flange to flange is 2-7/8", inside diameter at bead pattern area...

Replacement tank mounts can be used on Fat Bob tanks and also on custom frames where the mounts do not exist. Fits:FL 1955-1984Additional Information UOM

200 XL rigid frame features a 40  rake with a 3" stretch in front legs to accept a 1-1/8" belt with 200 series tire.Frame has kickstand tab and battery box mount welded in place. Accepts a right side...

V-Twin - 51-1955 - Replica inchHM inch Straight Leg Rigid FrameDescriptionReplica "HM" straight leg rigid frame is an authentic reproduction of the 1954-1957 straight leg frame with stock 30  neck...

Weld-on brake tab features a raw finish. Mounts stock or replica frames to the rear drum brake backing plate. Fits:FL 1958-1972Additional Information UOM

Footpeg support bar set is the splined type featuring a raw steel construction.Attaches to early Sportster frames to mount footpeg stanchions. One end is splined and the other fits over the frame...

Engine mount shim is used to raise motor for front or rear clearance, when necessary.Sold in a pack of 5. Fits:FL 1941-1999EL 1936-1952Additional Information

Engine bar features 1" tubing and a black finish.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow...

Raw steel weld-on hardtail features a raw steel finish.Replaces entire rear section of the frame, for the full rigid look. *NOTE: Must be installed by a certified welder. Fits:XL 1957-1978Additional...

Replica swingarm frame is our authentic reproduction of FLH style to accept a Panhead or Shovelhead engine, 4-speed transmission, seat post, and accepts a round or square swingarm. All components are...

Replica swingarm frame is an authentic reproduction of FLH style for 1965-1984.Frame accepts Panhead or Shovelhead engine, 4-speed transmission, 12v battery and round swingarm for drum brake...

Raw frame swingarm features forged axle plates for 3/4" axle with round tube construction. Fits:FX 1971-1972FL 1958-1972Additional Information OEM No.

This replica authentic style frame neck web repair section must be welded in after cutting stock or custom frame. It features the right side lock housing.Order new lock assembly, separately. Fits:FL...

Frame hardtail is bolt on type. Accepts drum style brakes on a rigid frame.Unit should be aligned for chain clearance prior to final bolting. DIY hardtail is easy to install as the alignment is...

Frame hardtail replaces shocks on swingarm frames and is drum brake type. Unit should be aligned for chain clearance prior to final welding.DIY hardtailing is easy to install as the alignment is...

Engine bar set features left and right sides.Two piece set. **WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while...

Chrome front engine bar features 1-1/4" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low...

Engine bar features 1" tubing.WARNING: This engine/frame bar may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very slow speed slide). They...

XL brake cross shaft kit includes two bushings. Kit must be welded in place. Fits:XL 1952-1976Additional Information UOM1 - KIT

Rigid hardtail frame raw steel rear section is 1957 style replica construction with components featuring the factory details of the period.The rear transmission mounts are 2" from the bottom cross...

Replica rear hardtail frame section is duplicated from an original rigid frame of 1957. Left axle plates are forged steel as OE. Weld-on type. The axle slots are 7/8" on both sides.Full replica...

Chrome finish dropped swingarm features a raised up axle position, so this lowers the swingarm and chassis in relation to the axle. Axle slots are 3/4", for disc brake applications.Lowers bike 1/2"...

This raw steel full rear section hardtail for Sportsters includes the rear motor mount and 4 bolt plate mount with upper and lower tube set. Frame is used to replace the stock rear motor mount and...

Lower frame gas tank mount set is without cross bracket. It includes the right and left tabs. Tabs are constructed of st eel and have a raw finish.May require finishing prior top installation and...

This 5th Mount transmission frame repair tab is weld on style for stock frames. The tab is constructed of steel and has a raw finish.May require finishing prior to installing. Fits:FX 1971-1984FL...

Rear pipe frame tab. Fits: FL 1958-1984 Additional Information UOM 1 - EA Manufacturer V-Twin

Brake line tee tab. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA Manufacturer

Cable mount frame tab is for under tank. Fits:FL 1955-1972Additional Information UOM1 - EA Manufacturer

Upper shock frame mounts are weld on style for stock frames.Sold as a set of two. Fits:FL 1965-1984FX 1971-1984Additional Information UOM1

Casting top seat mount is for frame seat post, frame back bone and frame upper seat rail yoke. Fits:FL 1958-1984Additional Information UOM1 - EA

Frame mount tab set for solo seats have weld on mount tabs. Use with T bar and pivot bolt to mount K and CH solos. Fits:XL 1957-1979Additional Information UOM

This weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM<

Rigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

Rear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA

Rear tank frame mount tabs. Fits:FL 1941-1984EL 1936-1947U 1937-1948Additional Information UOM1 - SET

Weld on frame footpeg mount without thread.Mount can be welded to 1958-1977 swingarm frames to utilize the stock FXE mount and raise the peg position. Sold as a pair. Fits:FX 1971-1978FL...