1970

Kit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information

Replica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes...

XL raw brake shaft tube for mechanical brakes. Kit includes machined 7.25" tube with brass bushing and shifter cross bushing set installed. Must be welded in place to frame.*NOTE: Locate tube using...

Steering lock assembly kit includes complete key assembly, key lock, two keys, spring, pin, plunger, frame plug, and neck casting piece for lock. Must be welded in place.Steering lock assembly kit...

Beaded windshield is a fixed mount type which comes completely assembled.Includes beaded windshield top and an adjustable lower windshield to fit FL aluminum headlamp cowl assembly. The center bolt...

Top beaded windshield measure 18" and is for use on fiberglass fairings only.Fits 1969-1984 FLH 4 speed and 1980-1985 FLT 5 speed models with Batwing fairings. Fits:FLT 1980-1985FLH...

Top beaded windshield is short style. Fits:FLH 1949-1984Additional Information OEM No.58020-49A UOM1

Frame saver mounting kit for gas tanks must be welded to Big Twin stock or custom frames. Casting features provision for damper pin, as required on 1949-1984 Big Twins.*Note: Includes speedometer...

Replica wishbone frame is an authentic reproduction of a 1948 Big Twin rigid frame with seat post, axle, and transmission plate already installed. The legs are smooth and do not have horn mount...

Solid steel frame dowel set is for the installation of hardtails.Outer diameter on small end is .7225 and large end is .8375. *NOTE: Must be welded in place. Fits:FL 1958-1984Additional Information

V-Twin - 50-2064 - Lindby Custom Front Engine BarDescriptionFront engine bar feature 1-1/8" tubing with built in O-rings on the footpeg area.Front engine bar is constructed of a high strength steel...

Raw alignment clips are for hinged rear fenders, to be spot welded on the front portion of the fender.Sold as a pair. *NOTE: Used to align and hold the rear tail flap edges in place. Fits:FLH...

Swingarm rear fender hinge features a raw finish. Hinge includes both halves with pin but without wire loom tail.Hinge halves are produced with correct pin and hinge offset for installing on original...

Raw steel wire loom fender strip for inside of the left FL rear hinged fender, radiused to fit the fender contour, and segmented to accept tail lamp wires.Must be spot welded to the left side or...

Wire loom spring clamp features a raw finish and is for use with the rear fender. To hold spring loom cover in place use #32-2036. Clamp is sold in a pack of 5.*NOTE: Must be spot welded on. Fits:FL...

FL fender strut set features a chrome finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. The distance from the...

FL fender strut set features a black finish solid lazer cut from heavy duty steel.Allows custom fenders to be mounted at the height desired for seat position requirements. *NOTE: Requires 7-1/4"...

V-Twin - 50-1148 - Zinc Plated Fender BracketDescriptionZinc plated steel bracket used to adapt one piece FXDF front fenders to fit FLH forks on 1949-up 41mm models.Set of two. Bracket is formed from...

Front fender trim kit includes chrome front fender tip and front fender trim side rails for FL models. Fits:FL 1967-1972Additional Information UOM1 - SET

Bobbed rear fender kit includes a steel fender, cateye tail lamp, chrome tail lamp bracket, and chrome struts.We suggest pre fitting fender prior to painting. Order sissy bar components separately. ...

2022 New Production Replica rear fender is flip style with updated hinged tail.Fender will accept 1955-1972 type tail light. We suggest pre fitting the fender prior to painting. Before priming or...

Chrome rear fender strut set is of solid steel construction and is for use with Bobbed fender only. Fits:FX 1973-1984FL 1958-1984Additional Information U

V-Twin - 50-0625 - XL Rigid Tool Box KitDescriptionLeft side tool box kit is the weld on type for rigid frames on Sportster builds.*NOTE: Weld bracket to lower rigid frame hardtail tube position or...

Magneto advance plate screw set includes four allen flathead screws and 2 hex screws with lock nuts.Kit includes 4 tapered screws for mounting base to magneto head. Fits 1965-70 XL with Magneto cable...

Drag Specialties - DS325386 - Rear Brake Shoes - '63-'72 Big TwinFeaturesHigh-quality brake shoesReplacement Part for OEM Number(s):4180163Specs

Drag Specialties - DS317463 - Battery Strap - '70-'78 FX/XLCHFeaturesHigh-quality replacement battery strapsMeets or exceed OEM specificationsSpecs

Drag Specialties - DS272097 - ignition Switch - '36-'72 Big TwinFeaturesReplacement ignition and light switch with lock for Fat Bob-style dash panelsMeets or exceeds all OEM specificationsIncludes...

Drag Specialties - DS240360 - Fork Boots - 41 mm - FL/FLH '48-'77 (Early)FeaturesMolded rubber constructionReplacement Part for OEM Number(s):4598373Specs

Drag Specialties - DS240215 - Long Clutch Lever Rod End - '36-'78 FLFeaturesRod end for long "mousetrap" clutch lever rodReplacement Part for OEM Number(s):3691636Specs

Drag Specialties - 24010850 - Board Mount Screws with Nuts - FrontFeaturesHas all required hardware for mounting driver floorboards to the mount bracketsIncludes four shouldered bolts and four...

Drag Specialties - 21130669 - Black Battery Cable Set - '65-'84 FLFeaturesBlack cable manufactured with pure electrolytic-grade, 36-gauge tinned copper strands for maximum current transfer and...

Drag Specialties - 21130216 - Battery Kit - CHD4-12FeaturesMSDS Migration DataDrag Specialties Conventional batteries are built to the same exacting specifications and quality-control standards as...

Drag Specialties - 21130215 - Battery Kit - CB7-AFeaturesMSDS Migration DataDrag Specialties Conventional batteries are built to the same exacting specifications and quality-control standards as OEM...

Drag Specialties - 21130298 - Battery Cover - Smooth - ChromeFeaturesFeatures precise formed covers for sealed and conventional batteriesThe use of AGM sealed maintenance-free batteries requires...

Drag Specialties - 21121204 - 32A Charging Kit - Black RegulatorFeaturesKit includes an encapsulated magnetic rotor, precision-wound stator and an 89-99 32A chrome voltage regulatorFeatures a thick ...

Drag Specialties - 21121078 - Regulator - XL '65-'77 - BlackFeaturesFully assembled in the USA with domestic made electrical boardsTested three different times during the assembly process to ensure...

Drag Specialties - 21120927 - Regulator Mount - Harley Davidson - BlackFeaturesAllows the regulator to be mounted down and back out of sightOptional 10-24 holes on back of mount for ground wireMade...

Drag Specialties - 21120822 - Regulator - 12 Volt - BlackFeaturesHigh-reliability voltage regulators feature rugged aluminum alloy constructionProvides accurately regulated voltage under all...

Drag Specialties - 21120780 - Regulator - '70-'75 Big Twin - BlackFeaturesHigh-reliability voltage regulators feature rugged aluminum alloy construction and are available in Drag's chrome...

Drag Specialties - 21100327 - Starter SolenoidFeaturesDesigned with extra current capacity for starting high-compression motorsRecommended for use with Drag Specialties High Performance...