Softail Heritage FLST

Jims - 2233 Tappet Oil Filter Plug Tool fits '70-'99 Big Twin Models Features: Removes oil screen without removing exhaust Used to rem

Jims - 39361-69 Sprocket Shaft Seal Installation Tool fits '69-'10 Big Twin & Twin Cam Models Features: Designed to press oil seal over sprocket shaft into case

Jims - 35316-80 5-Speed Main Drive Gear Tool fits '80-'06 Big Twin (Except '06 Dyna) & '91-'06 Sportster Models Features: Installs the main drive gear without removing the transmission

Jims - 34902-84 Mainshaft Bearing Race Tool fits 'L84-'20 Big Twin Models Features: Used to remove and install the inner bearing race on the transmission mainshaft Made in the U.S.A.

Jims - 34734-80 Main Drive Gear Bearing/Seal Installer Tool fits '80-'90 5-Speed Big Twin Models Features: Holds bearings and seal square to its bore, eliminating any marring Install both b

Jims - 34623-83 Piston Pin Tool fits '84-'99 Big Twin (Except Twin Cam), '86-'03 Sportster Models Features: This tool will install “Round Circlip” rings in one easy step without distorting ring,...

Jims - 34643-84 Valve Seal Installer for all Evolution Valve Guide Seals (OEM #34643-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as...

Jims - 1010 Evolution Rod Alignment Tool for 0.791” Wrist Pin Features: Use to check rod straightness without removing the rods from the cases Made in the U.S.A.

Jims - 1012-70TB Cam Bushing Installer fits '70-'99 Big Twin Models (Except Twin Cam (OEM #25581-70)) Features: Use to install bushing and drill dowel pin hole to factory specification #31

Jims - 94805-57 Pinion Bushing Line Reamer fits '54-'99 Big Twin Models (Except Twin Cam) Features: Use on all Big Twin '54-'99 single cam only, (NOTE: Includes aftermarket motors, also XL '57 to...

Jims - 1041-TC Camshaft Cover Holder Tool fits '70-'99 Big Twin Models (Except Twin Cam) Features: Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings

Jims - 95970-32C Piston Pin Bush Tool fits '36-'99 Big Twin, '57-'20 Sportster & Buell Models (Except 1125R) Features: Use to remove and install wrist pin bushings without removing rods from...

Jims - 2232 Bearing Race Tool fits '84-'17 Big Twin (Except '14-'17 Dressers), '86-'22 Sportster & '94-'02 Buell OEM Frames (Will Also Work on Most Aftermarket Frames) Features: Removes and...

Jims - 96600-36B Valve Spring Compressor Tool fits '36-'04 Big Twin & '57-'03 Sportster Models Features: Comes with new valve collar receiver for safer tool usage, and can be clamped in vice

Jims - 97225-55 Sprocket Shift Bearing Installation Tool fits '55-'02 Big Twin Models Features: Used on '84-'02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearing

Jims - 34731-84 Valve Guide Installer fits all Evolution & '99-'04 Twin Cam Models (OEM #34731-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve...

Jims - 1047-TP Crank Assembly Removal Tool fits '55-'06 Big Twin Models (Except '06 Dyna) Features: This tool can only be used for removing the flywheel from the left case Will also press c

Jims - 1013-54TB Pin Bushing Installer fits '54-'92 Big Twin Models (OEM #25582-54/73) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length H

Jims - 1030-TS Crank Pin Flywheel Socket fits 'L83-'99 Big Twin Models (OEM #23969-83) Features: Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of inj

Jims - 33071-73 Bearing Race Remover and Installer fits '73-'99 Big Twin, Sportster & Buell Wheels Features: Designed to remove and install bearing cups in cast wheels

Jims - 94660-37A Counter Shaft Sprocket Locknut Wrench fits '36-'06 Big Twin Models (Except '06 Dyna) Features: Removes hex nut from end of main drive gear that secures the rear drive...

Jims - 95760-TB Puller Camshaft Bearing fits '58-'99 Big Twin Models (Except Twin Cam) Features: Used to remove inner cam bearing without damaging the crankcase Tool is also designed to kee

Jims - 95760-TP Pinion Bearing Puller fits '54-'99 Big Twin Models Features: Use to remove pinion bushing from cam cover in one easy operation Use with JIMS® Cam Cover Holder

Jims - 95960-52C Clutch Hub Puller fits '36-'90 Big Twin Models Features: Used to remove wet and dry clutch hubs without removing clutch release rod 4 bolts included for dry clutch removal<

Custom Cycle Engineering - 41 mm Ultra Chrome Fork Tubes fits 'L84-'99 Softail, '85-'86 FXWG, '93-'98 FXDWG, '85-'96 Touring Models (OEM #45827-84, 45417-84) Features: Designed to fit a wide...

Colony - 9877-2 Cadmium Oil Screen Plug fits '70-'80 Big Twin Models (OEM #657) Features: Oil Screen plug for Big Twin models Made in the USA

Colony - 3547-5 Sprocket Bolt Zinc Plated Washer Kit fits '82-'94 FXR, '91-'17 FXD, '79-Up Sportster Models Zinc plated spring steel washers used on 7/16" rear sprocket bolts Fitment: FXST...

Colony - 9854-28 Chrome Upper and Lower Engine Bolts fits '84-'99 FXST, '86-'99 FLST Models Upper and lower engine mount bolts with a chrome finish  Fitment: FXST 1984-1999 FLST 1986-1999

V-Twin - Chrome Pike Style Axle Kit fits '84-'99 FXST & '86-'99 FLST Models Custom rear pike style has a 12-3/8" bearing surface length Fitment: FXST 1984-1999 FLST 1986-1999 Measurements: Bearing...

Colony - 9870-16 Inner Primary Mount Kit fits '91-'93 FXD, '86-'93 FXST/FLST Models Inner primary mount kit contains all stock type hardware for mounting aluminum inner chain housing...

Colony - 9964-2 Chrome Washer Fork Tube Plug fits '84-Up FXST, '77-'86 FX, '86-Up FLST Models (OEM #5710) Chrome fork tube plug washer Fitment: FXST 1984-UP FX 1977-1984 FLST 1986-UP FX...

Colony - 9977-1 Chrome Fork Triple Tree Stem Cap fits '84-Up FXST,  '86-'94 FXR, '86-Up FLST/Sportster Models Chrome fork triple tree stem cap Fitment: FXST 1984-UP XL 1986-UP FXR...

V-Twin - Spark Plugs Nickel fits '75-'85 FL/FX Models V-Twin performance spark plugs features a nickel core electrode for a longer service life, alloy housing, 95% pure alumia insulator and a heat...

V-Twin - Nickel Spark Plugs fits '75-'85 FL/FX Models V-Twin performance spark plugs features a nickel core electrode for a longer service life, alloy housing, 95% pure alumina insulator and a heat...

V-Twin - 52" Inline Spring Fork Assembly fits Custom Application Unit features chrome springs, and rockers, front and rear leg in black. This 52" assembly is 20" over stock length. Includes inner and...

Colony - Universal Line Fitting fits '52-'99 Big Twin & '57-'85 Sportster Models (OEM #63578-52) Features: OEM replacement restoration For use with 5/16" hose

Colony - 9876-2 Chrome Oil Screen Plug fits '70-'80 Big Twin Models (OEM #657) Features: Oil Screen plug for Big Twin models Made in the USA

Mueller Motorcycle AG - Power Clutch fits '99-'23 Big Twin Models w/ Mechanical Clutch Features: The original Müller Power Clutch Replaces OEM inner and outer ramp assemblies

Pro-One - Pro Board V2 Floorboards - fits '84 & Up FLH/FLHT, '86-'17 FLST Features: Include traditional BMX style traction pins that provide fantastic grip Thin tapered design for additional...

Drag Specialties - 54-3/4" Black Vinyl High-Efficiency Clutch Cable (Repl. OEM #38699-04) Features: Cables feature chrome fittings, black vinyl outer casings, tempered-steel inner wire and a...