Tools

V-Twin - 16-1726 - 1-1/2 inch Lap Head Pilot Tool SetDescription1-1/2" lap head pilot tool set is the engine type.Sold as a 4 piece set. *NOTE: For Eastern tool only. Fits:FL 1941-1953EL 1936-1952VL 1930-1936Additional Information OEM No.96715-40 UOM1...

V-Twin - 16-1724 - Lap Head PilotsDescription1-1/4" lap head pilot tool is the engine type, for the Eastern tool only. Fits:FL 1956-1969Additional Information OEM No.96727-56 UOM1 - EA ManufacturerEastern OriginUSA 2025 Catalog Pages1276

V-Twin - 16-1688 - 4-Speed inch88 inch Roller Spacer ToolDescription4-speed "88" roller spacer tool is used to mimic the 88 roller spacing setting end play. Fits:FL 1944-1976EL 1936-1952Additional Information UOM1 - EA ManufacturerV-Twin ...

V-Twin - 16-1677 - Gasket Alignment Stud Tool SetDescriptionGasket alignment stud tool set includes two 1/4" x 20 and two 1/4" x 24 threaded studs, with slotted screw head. Install to hold oil pump gaskets in place.Sold as a 4 piece set. Fits:FL...

V-Twin - 16-1672 - Jims Crankshaft Bearing ToolDescriptionThis crankshaft locking tool locks all crankshafts by engaging the pinion shaft splines. This allows removal and torquing of the pinion nut during installation. Fits:FLT 2003-UPFLST 2003-2017FXST...

V-Twin - 16-1670 - 4-Speed Main Drive Gear Tool NutDescription4-speed main drive gear tool hex nut.*NOTE: Must order sleeve separately. Fits:FL 1941-1976EL 1936-1952Additional Information UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog...

V-Twin - 16-1669 - Jims Compensator Bolt Torx SocketDescriptionJims compensator bolt torx socket is for 2014-up Big Twins. Used to remove or install the compensator bolt. Fits:FXD 2014-2017FLST 2014-2017FXST 2014-2017FLT 2014-UPAdditional Information ...

V-Twin - 16-1663 - V-Twin Compensator Sprocket WrenchDescriptionV-Twin compensator sprocket wrench is used to easily install or remove compensating sprockets. Features 1/2" drive. Fits:FL 1955-1969Additional Information UOM1 - EA ManufacturerV-Twin ...

V-Twin - 16-1652 - Mainshaft Seal Remover and InstallerDescriptionThis mainshaft tool is used to install and remove the main seal in 4-speed transmissions.It will push the seal in as flat and straight as possible to .050 below housing for a no leak fit...

V-Twin - 16-1645 - Sifton Mainshaft Bearing Race ToolDescriptionSifton mainshaft bearing race tool.*NOTE: Replacement parts like the race pusher tube, are available separately. Fits:FXD 1991-2005FLST 1986-2006FLT 1987-2006FXST 1986-2006FXR...

V-Twin - 16-1641 - Backing Washer Puller ToolDescriptionBlack oxide finish backing washer #17 puller tool. Fits:FX 2000-UPFLT 2000-UPAdditional Information UOM1 - EA ManufacturerMotorshop OriginImported 2025 Catalog Pages1293 Tech NoteSuggested to...

V-Twin - 16-1634 - Mini Air CompressorDescriptionMini air compressor features a compact design to fit inside a saddlebag or car.Includes 2' of hose and end to fill tire valves up to 35 pounds. ...

V-Twin - 16-1615 - Chain Puller ToolDescriptionChain puller tool. Fits:AllAdditional Information UOM1 - EA ManufacturerMotorshop OriginImported 2025 Catalog Pages1290

V-Twin - 16-1514 - Clutch Compression ToolDescriptionClutch compression tool has adapter included Fits:FLST 1990-2017XL 1991-UPFXD 1991-2017FXST 1990-2017FLT 1990-UPFXR 1990-1994Additional Information UOM1 - EA ManufacturerMotorshop OriginImported ...

V-Twin - 16-1505 - Sprocket Nut Wrench Tool CollarDescriptionNut lock wrench collar features parkerized finish. Fits:FL 1941-1984Additional Information UOM1 - EA ManufacturerMotorshop OriginImported 2025 Catalog Pages1289 Tech NoteSuggested to use...

V-Twin - 16-1503 - Pingel Wheel Chock with Mounts 21 inch OnlyDescriptionThe wheel chock features quick mounting and removal by sliding in and out of slotted mount pads and secures a motorcycle on your wood floor trailer.Chock is a chrome steel tube...

V-Twin - 16-1405 - Linkert Tool KitDescriptionLinkert tool kit includes 6 special drills with brass knurled handles, 1 idle shot tool, and 1 venturi tool for use on brass linkert carburetor bodies, all years.Kit includes 6 drill pivots and 1 idle slot...

V-Twin - 16-1404 - Linkert Hand Tool Tap 5/16 inch X 32DescriptionLinkert hand tool tap 5/16" X 32 thread. Fits:FL 1941-1965Additional Information UOM1 - EA ManufacturerMotorshop OriginImported 2025 Catalog Pages1279

V-Twin - 16-1403 - Linkert Hand Tool Tap 5/16 inch X 18DescriptionLinkert hand tool tap 5/16" X 18 thread. Fits:FL 1941-1965Additional Information UOM1 - EA ManufacturerMotorshop OriginUSA 2025 Catalog Pages1279

V-Twin - 16-1401 - Linkert Hand Tap Tool 12-24DescriptionLinkert hand tool tap 12-24 thread. Fits:FL 1941-1965Additional Information UOM1 - EA ManufacturerMotorshop OriginUSA 2025 Catalog Pages1279

V-Twin - 16-1400 - Linkert Hand Tool Tap 10-32DescriptionLinkert hand tool tap 10-32 thread. Fits:FL 1941-1965Additional Information UOM1 - EA MeasurementsAdditional InformationOverall Length: 3.9370"Shank Diameter: 0.4375" ...

V-Twin - 16-1392 - Cam Bearing Puller ToolDescriptionCam bearing puller tool removes the inner cam needle bearing #9057, without splitting the cases while preventing the rollers from coming out during removal.For use with bearing, as listed. ...

V-Twin - 16-1391 - Cam Bearing Remover ToolDescriptionCam bearing remover tool allows the removal of needle bearings while keeping the needles from falling into the engine.For use with bearing, as listed. ...

V-Twin - 16-1390 - TC-88 Inner Cam Bearing ToolDescriptionThis four piece tool safely installs the inner cam bearings to the proper depth in the case without damaging bearings.Complete 8 piece tool by V Twin manufacturing. Fits:FLST 1999-2006FXST...

V-Twin - 16-1378 - Shaft Turning ToolDescriptionThis Jims shaft turning tool fits spline or taper on assembled motor and allows engine to be turned over by 1/2" ratchet or impact driver. Fits:FLT 2007-2016FXD 2006-2017FLST 2007-2017FXST...

V-Twin - 16-1375 - Jims Case Bearing Conversion ToolDescriptionUsing the special Jims precision insert, this tool is designed to easily and accurately convert the left side crank roller bearing to the more durable Timken Bearing.This tool includes one...

V-Twin - 16-1371 - Wheel Bearing Installer ToolDescriptionWheel bearing install tool is to be used with 25mm bearing, including ABS and non ABS bearings.*NOTE: Required to use with the wheel bearing puller/installer tool, availble separately. Fits:FXD...

V-Twin - 16-1368 - Starter Ring Gear Rivet Fixture ToolDescriptionThis tool removes the starter ring gear rivets from clutch shells. Fits:FXD 1991-2005FLST 1990-2006FLT 1990-2006FXST 1990-2006Additional Information UOM1 - KIT ManufacturerJims ...

V-Twin - 16-1364 - Sprocket Shaft Bearing and Seal Installation Tool AdapterDescriptionThis excellent tool upgrades Jims bearing installer tool for work on fine splined Twin Cam sprocket shafts.Allows for installation of Timken bearings and roller...

V-Twin - 16-1363 - Main Drive Gear Seal InstallerDescriptionThis tool allows for perfect installation of the main drive gear oil seal on the assembled transmission to its proper depth.The protective sleeve which is included is used to protect the inner...

V-Twin - 16-1357 - Primary Locking ToolDescriptionThe Jims primary locking tool is used to lock the clutch hub sprocket to the front engine sprocket. It also allows the removal or torquing of clutch hub and engine nut. Fits:FXD 2006-2017Additional...

V-Twin - 16-1356 - Transmission Trap Door Puller ToolDescriptionJims right side drive transmission trap door puller tool removes the access door on all right sided drive transmissions. Fits:FXD 2006-2017FLST 2007-2017FLT 2007-UPFXST 2007-2017Additional...

V-Twin - 16-1354 - Jims Case Splitter ToolDescriptionUse this tool to expertly and safely break the case sealant by pushing apart both halves.This tool bolts to the primary mounting holes with supplied hardware. Hand thread in pushing screw. The...

V-Twin - 16-1352 - Jims Cam Locking ToolDescriptionThe cam locking tool allows the removal and torquing of cam sprocket bolts by locking camshaft and camshaft sprockets. Fits:FLT 2007-2016FXD 2006-2017FLST 2007-2017FXST 2007-2017Additional Information ...

V-Twin - 16-1344 - Glide Fork Nut ToolDescriptionGlide fork nut double ended wrench feature a black oxide finish. Used for removing and installing crenulated nuts and dust covers with internal thread. Fits:FL 1949-1969Additional Information UOM1 - EA ...

V-Twin - 16-1297 - Starter Jack Shaft Lock WrenchDescriptionJack shaft lock wrench is zinc plated. This tool is used to hold starter gears on 1991-up Big Twins. Fits:FX 1991-UPFLT 1991-UPFXR 1991-UPFL 1991-UPAdditional Information UOM1 - EA ...

V-Twin - 16-1287 - Jims Cylinder Torque PlateDescriptionThe Jims torque plate is lasered with correct torquing sequence and will also work on Eagle big bore cylinders. Fits:FLT 1999-2016FLST 1999-2017FXST 1999-2017FXD 1999-2017Additional Information ...

V-Twin - 16-1283 - Jims Cam Gear Remover ToolDescriptionThe cam gear remover tool is used to remove the cam gear from the camshaft.The tool acts as a stable base to keep the camshaft perpendicular to the press. Fits:FL 1970-1984FXST 1984-1998FXR...

V-Twin - 16-1282 - Jims Cam Gear Alignment ToolDescriptionThis alignment tool is designed to index the cam gears position while removing on installing the cam gear. You will be able to accurately position the cam gear from one camshaft to another...

V-Twin - 16-1281 - Jims Crank Shaft GuideDescriptionUse this crank shaft guide to spread pinion bearing rollers while reassembling right side engine case on to flywheel assembly. Fits:FLT 1999-2016FLST 1999-2017FXST 1999-2017FXD 1999-2017Additional...