Bagger Parts

James Gasket - Top End Gasket Kit fits '92-'99 4” Bore Evolution Models (OEM #17033-92) Features: Top-quality gaskets, oil seals and O-rings necessary to rebuild an engine Made in the USA Kit Includes: Head Gaskets with...

James Gasket - Cam Change Gasket Kit fits '93-'99 Evolution & Big Twin Models Features: Kit includes all necessary gaskets, seals, O-rings and cork washers for doing a cam change Fitment 2000 Harley-Davidson FXR...

James Gasket - Transmission Seal Kit fits '94-'98 Big Twin Models Features: Designed for most 4- or 5-speed Big Twin transmissions Made in the U.S.A. Fitment 1998 Harley-Davidson Road Glide FLTR - - 1998 Harley-Davidson Road...

James Gasket - Transmission Seal Kit fits '84-'93 Big Twin Models Features: Designed for most 4- or 5-speed Big Twin transmissions Made in the U.S.A. Fitment 1993 Harley-Davidson Wide Glide FXDWG - - 1993 Harley-Davidson Low...

Jims - 1733 Mega Nut fits '07-'20 Big Twin & '06-'17 Dyna Models Features: Includes machined clamping face tolerance, along with additional locking holes for a more precise and secure way to secure pulley nut Made in the U.S.A...

Jims - 981 Cruise Drive/6-Speed Main Drive Gear Tool fits '07-'17 Twin Cam & '06 Dyna Models Features: Holds the main drive gear square to its bearing bore, eliminating any marring of gear or bearings Installs the main drive gear without...

Jims - 986 Cruise Drive/6-Speed Main Drive Gear Bearing/Seal Installer Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Holds bearings and seal square to its bore, eliminating any marring Install both bearings and seal with use of a...

Jims - 984 Transmission Door Puller fits '07-'17 Big Twin & '06 Dyna Models Features: Removes transmission door with gears and shaft attached Made in the USA Puller will not damage door bearings...

Jims - 989 Main Drive Gear Sprocket Locknut Wrench fits '07-'21 Big Twin & '06 Dyna Models Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the USA Inner...

Jims - Shifter Shaft Removal Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Loosens and removes both shifter shafts from transmission door, allowing further disassembly of transmission Made in the...

Jims - 901 Cruise Drive/6-Speed Main Drive Gear Remover Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Removes the main drive gear from the main bearing correctly while in the transmission case Eliminates the need of an arbor press and...

Jims - 911 Cruise Drive/6-Speed Trap Door Bearing Remover/Installer fits '07-'20 Big Twin & '06 Dyna Models Features: Accurately installs and removes lubed ball bearing into transmission trap door No arbor press needed Made in the U.S.A...

Jims - 767 6-Speed Transmission Case Shifter Shaft Seal Installer fits '06-'20 Big Twin & '84-'05 Sportster Models Features: Makes installing shifter shaft seal precise and effortless Aligns, centers and installs shifter seal to correct...

Jims - 768 5-Speed Transmission Case Shifter Shaft Seal Installer fits '80-'99 Big Twin, '99 Twin Cam, '99-'06 FXST & '99-'05 FLT/F LHT/​FXD Models Features: Makes installing shifter shaft seal precise and effortless Aligns, centers and...

Jims - 1658 Transmission Shifter Shaft Sleeve Tool fits '06-'20 6-Speed H-D Cruise Drive Models Features: Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use to install shifter shaft sleeve Made in the...

Jims - 739 5 & 6-Speed Cruise Drive Countershaft Bearing Remover/Installer Tool Features: Install or remove the closed-end countershaft bearing on all 5-speed or 6-speed transmissions without using a press or tapping it in with a transmission...

Jims - 967-4 Installation/Removal Inner Primary Bearing Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also...

Jims - 967-5 Inner Primary Bearing Tool fits '07-'19 Big Twin & '06 Dyna Models Features: Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also removes and installs...

Jims - 5517 Removal/Installation Shifter Mechanism Sleeve Tool fits '06 Dyna & '07-'20 Big Twin w/ 6-Speed Cruise Drive Transmission Features: A real time saver for removing and installing the shifter mechanism sleeve in cruise drive Big Twin...

Jims - 1672 Crankshaft Bearing Tool fits '03-'17 Twin Cam “A” and “B” Motors Models Features: Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in...

Jims - 995 Case Splitter Tool fits '07-'17 Twin Cam & '06 Dyna Models Features: "Breaks" the case sealant by pushing apart both case halves Uses included hand thread-in pushing screw Flywheels will be pushed from the left case Bolts to primary...

Jims - 988 Valve Spring Compressor fits '05-'17 Twin Cam (Except SE Models), '04-'22 Sportster (Except RH Sportster) & Buell Models (Except 1125R) Features: Used to remove and replace valve and new-style conical valve spring Requires use of JIMS...

Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made...

Jims - 1664 5-Speed Transmission Shifter Shaft Sleeve Tool fits '80-'83 FLT/​FLHT/​FXR, '84-'99 Big Twins & '84-'00 FLHT/​FXR/​FXD Models Features: Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use...

Jims - 5530 Remote Fuel Tank fits H-D Models w/ Delphi Fuel Injection (Except V-Rod) Features: Tank is completely mobile, even when pressurized; canister does not need to be continuously connected to the air supply Small enough to hang from a...

Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 1989 Harley-Davidson Electra Glide Ultra...

Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

FLHRS Jims - 2043 41mm Fork Nut Socket fits '48-'17 Wide Glide Models Features: Eliminates possible burring of plug caused by wrenches Used to remove and install top fork-tube plug Fits 41 mm forks Made in the U.S.A...

Jims - 1705 Exhaust Drill Plate fits '84-'17 Big Twin (Except M-Eight), '86-'22 Sportster & '94-'09 Buell Models (Except 1125R) Features: Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made...

Jims - 95760-57 Bushing Bearing Puller fits '66-'17 Big Twin (Except M-Eight), '57-'22 Sportster & Buell Models (Except 1125R) Features: Used to remove rocker bushing or bearing in one easy operation Made in the U.S.A...

Jims - 38515-90 Clutch Spring Compressor fits '90-'97 Big Twin & '91-'03 Sportster Models Features: For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can...

Jims - 1710 Outer Race Snap Ring fits '69-'02 Big Twin Models Features: Used for removing and installing the Timken® bearing outer race snap ring A must for replacing rings in OEM and aftermarket cases Made in the U.S.A...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 2260 Sprocket Lock Tool fits '99-'17 Twin Cam & '80-'99 Big Twin Models w/ Rear Belt Drive Features: Lock the transmission pulley for removing or installing pulley nut Made in the U.S.A...

Jims - 2189 Transmission Shaft Installer fits '83-'06 Big Twin Models Features: Installs transmission shaft without the use of a hydraulic or arbor press Made in the U.S.A. Fitment 2008 Harley-Davidson Fat Bob...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...

Jims - 1725 Head Bearing Race Installer fits '36-'17 Big Twin Models w/ Stock or Custom Frames (Except '14-'17 Dresser) Features: Use to install steering head races, stock and custom, as well as install cups in the frame This tool pulls the races...

Jims - 2283 Transmission Door Puller fits '80-'06 Big Twin 5-Speed Models Features: Removes transmission door with gears and shaft attached Made in the USA Puller will not damage door bearings. Fitment 2006 Harley-Davidson Street...