V-Twin - 51-0545 - Lower Front Gas Tank Mount with Cross PlateDescriptionLower tank frame mount with cross plate.Must be welded in place. The mount hole center to center measures 1-3/4" and the small end grasp area sits 1-1/2" high from the plate...

V-Twin - 51-0534 - Crossover Shaft Frame BraceDescriptionRigid Big Twin crossover shaft frame brace comes in left and right. Fits:UL 1938-1947EL 1936-1940FL 1941-1957Additional Information UOM1 - SET ManufacturerV-Twin OriginImported TypeRigid

V-Twin - 51-0532 - Coil Mount Frame Block SetDescriptionThis weld on style coil mount frame block set repairs stock frames and has a 3/8"-24 UNF thread. Fits:FL 1956-1983FX 1971-1983Additional Information UOM1 - SET ManufacturerV-Twin OriginImported ...

V-Twin - 51-0530 - Frame Top Engine MountDescriptionFrame top engine mount is two halves with seat tee and rear tank mounts incorporated into the top mount. Weld in place for accurate restoration.*NOTE: Threaded for seat "T" bolt. Fits:FL...

V-Twin - 51-0529 - Front Oil Tank Mount Frame CastingDescriptionRigid frame front oil tank mount casting to be welded on.Thread is 5/16 x 24 and the lip from the bottom to the top measures 1-1/4". For use with 1-1/2" bar. Fits:FL 1941-1984FX 1972-1984EL...

V-Twin - 51-0527 - Rear Frame Engine Mount and Front Transmission MountDescriptionRear frame engine mount and front transmission mount. Fits:FX 1971-1984FL 1958-1984Additional Information UOM1 - EA ManufacturerV-Twin OriginImported TypeRigid 2025...

V-Twin - 51-0525 - Neck Frame Forging with Key HoleDescriptionNeck frame forging has a 30  rake with key hole. Machined to accept neck lock tumbler.Forged neck is accomplished in 4 stages: First the steel is fired as red hot ingot, next huge hammers...

V-Twin - 51-0524 - Neck Frame CastingDescriptionNeck frame casting fits XL models to be welded in place on 30  stock or custom frames. Has unmachined padlock boss. Accepts neck cup kit.Neck frame accepts stock bearing cups and trees. Fits:XL...

V-Twin - 51-0522 - Rear Frame Engine Mount and Front Transmission MountDescriptionRigid frame rear engine mount and front transmission mount. Fits:UL 1938-1947EL 1936-1940FL 1941-1957Additional Information UOM1 - EA ManufacturerV-Twin OriginImported ...

V-Twin - 51-0520 - Frame Neck without CupsDescriptionBig Twin neck forgings machined to accept stock diameter tubing with 30  rake.Includes key lock tab and right hand number boss forged in neck. *NOTE: This frame neck does not include Manufacturer's...

V-Twin - 51-0515 - Kickstand Frame Mount UniversalDescriptionUniversal weld on kickstand frame mount. Fits:Custom applicationAdditional Information UOM1 - EA FinishRaw ManufacturerV-Twin OriginImported 2025 Catalog Pages915

V-Twin - 51-0513 - Right Side Caliper Frame Mount BracketDescriptionRight side caliper frame mount bracket for left side drive motorcycles must be welded on. Bracket is for rigid frames when mounting brake units. Fits:Custom application for right...

V-Twin - 51-0512 - Frame Anchor Mounting TabDescriptionWeld on type caliper arm mount tab is for disc brake models on rigid frames. Fits:Custom application for restoration or repairAdditional Information UOM1 - EA ManufacturerV-Twin OriginUSA ...

V-Twin - 51-0511 - Hydraulic Rear Drum Frame TabDescriptionHydraulic rear drum weld on frame tab fits rigid frames when mounting brake units. Fits:FL 1958-1972Additional Information UOM1 - EA ManufacturerPaughco OriginUSA TypeRigid 2025 Catalog...

V-Twin - 51-0508 - Frame Side Car Loop SetDescriptionRigid frame side car loop set to be welded on for restoration or repair. The loops are machined spools. Fits:EL 1936-1940FL 1941-1957Additional Information UOM1 - SET MeasurementsAdditional...

V-Twin - 51-0506 - Frame Gusset Plate Left SideDescriptionNew Old Stock" Frame gusset plate is for the left side on swingarm frames.New Old Stock from the 1980's, part has rust and oxidation! Fits:FL 1958-1968FLH 1958-1968Additional Information OEM No...

V-Twin - 51-0503 - Frame 5th Transmission MountDescriptionRigid frame 5th transmission mount to be welded on for restoration or repair. Fits:EL 1936-1940FL 1941-1957Additional Information UOM1 - EA ManufacturerV-Twin OriginUSA TypeRigid 2025 Catalog...

V-Twin - 51-0502 - Front Frame Mount Block Right Side Two Hole TypeDescriptionRigid frame brake mount block for front right side of frame is two hole type. Weld on for restoration or repair. Fits:Custom application for restoration or repairAdditional...

V-Twin - 51-0501 - Front Frame Mount Block Left Side Three Hole TypeDescriptionRigid frame shift mount block for front left side of frame is three hole type. Weld on for restoration or repair. Fits:Custom application for restoration or repairAdditional...

V-Twin - 51-0486 - Mid Control Mount Kit BlackDescriptionMid control mount kit is used to mount to the two holes located in the lower frame brace. Kit features a black finish.Mount features holes on each side for the left and right foot brake peg mount...

V-Twin - 51-0485 - XL Control Mount Set BlackDescriptionXL control mount set features a black finish. Control mounts for right (2 bolt plate) and left (3 bolt plate) to accept Big Twin forward controls.Set is used to mount 1941-1999 Big Twin forward...

V-Twin - 51-0484 - XL Hardtail Axle Plate SetDescriptionRaw set of right and left axle plates for Sportster hardtails, features 7/8" slots on both sides. Fits:XL 1982-UPAdditional Information UOM1 - SET ManufacturerV-Twin OriginImported

V-Twin - 51-0481 - Brake Cross Shaft KitDescriptionBrake cross shaft kit is for stock and replica rigid frames.Includes right side tube with bushing, strap bracket set and grease fitting. Fits:FL 1941-1957EL 1936-1948Additional Information UOM1 - KIT ...

V-Twin - 51-0474 - Motor Adapter KitDescriptionKit mounts to adapt 1957-1985 Ironhead motors into 1986-2003 XL rigid frames.Ironhead motor installation kit includes front and rear mounts and hardware. Fits:XL 1957-2003Additional Information UOM1 - KIT ...

V-Twin - 51-0473 - Neck Lock Pin Raw SteelDescriptionRaw steel neck lock pin only. Fits:FL 1948-1968VL 1930-1936Additional Information UOM1 - EA ManufacturerV-Twin OriginImported

V-Twin - 51-0472 - 45 inch Front Engine Clutch Cable Mount RawDescription45" front engine clutch cable mount features a raw finish and must be welded to the center tube. Fits:G 1941-1973W 1941-1952Additional Information UOM1 - EA ManufacturerV-Twin ...

V-Twin - 51-0471 - Front Engine Brake StrapDescriptionFront engine brake strap. Fits:W 1936-1952Additional Information UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages815

V-Twin - 51-0470 - Front Engine Coil MountDescriptionFront engine coil mount. Fits:W 1936-1952Additional Information UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages815

V-Twin - 51-0469 - Front Engine Top Motor MountDescriptionFront engine top motor mount. Fits:W 1936-1952Additional Information UOM1 - EA ManufacturerV-Twin OriginImported 2025 Catalog Pages815

V-Twin - 51-0467 - 45 inch Transmission and Motor Base Forging Set RawDescription45" transmission and motor base forging set holds transmission and connects center post and front down tube.2 pieces welded as an assembly. Fits:W 1936-1952Additional...

V-Twin - 51-0465 - 45 Weld-On Frame HardtailDescriptionWeld on hardtail assembly features a raw finish, forged cross bar and rear axle plates on original WL 45 solo's.Installation requires a qualified fabricator and welder. Must be welded on and the...

V-Twin - 51-0463 - XL Rear Motor Mount Pad TallDescriptionXL rear motor mount pad is the tall type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA ManufacturerV-Twin OriginImported

V-Twin - 51-0462 - XL Rear Motor Mount Pad ShortDescriptionXL rear motor mount pad is the short type, featuring a cast steel construction. Fits:XL 1982-2003Additional Information UOM1 - EA ManufacturerV-Twin OriginImported

V-Twin - 51-0461 - Front Engine Mount Frame BraceDescriptionFront engine mount weld on frame brace for 45 solo frames.*NOTE: Frame parts are forged and machined using tooling exclusively by V-Twin MFG. Fits:W 1936-1952Additional Information UOM1 - EA ...

V-Twin - 51-0460 - 45 inch Replica Rigid Cast Neck Raw SteelDescription45" Side Valve Rigid cast neck is constructed of raw steel forging and is machined to accept stock size frame tubes.Accepts 7/8" neck cups, not included. *NOTE: Frame parts are forged...

V-Twin - 51-0459 - 45 inch Rear Frame Engine and Front Transmission Mount ForgiDescriptionRear frame engine mount and front transmission mount for 45 solo frames, and features a raw steel construction.Has a hole for the rear clutch and brake strap shaft,...

V-Twin - 51-0458 - 45 Front Control Rod Forging RawDescription45 front control rod forging features a raw finish.Braze on to front down tube to support brake and clutch strap, and jiffy stand on the left side. Fits:W 1936-1952Additional Information UOM1...

V-Twin - 51-0457 - Replica Frame HardtailDescriptionReplica rear hardtail frame section is duplicated from an original rigid frame. Weld-on type and does not have seat post bushing.The rear transmission mounts are 1-1/2" tall. This hardtail includes rear...

V-Twin - 51-0456 - Rear Frame Axle Plate SetDescriptionRear frame right and left axle plates with oiled raw steel finish for 45 solo frames, constructed of forged steel.Must be welded in place. ...

V-Twin - 51-0438 - Softail Top Frame PlateDescriptionSoftail top frame plate features a raw steel finish, to match with seat area plate on 1986-1999 Softail original frames.For Hardtail installation. *NOTE: Align with the (2) 1/4" holes in plates. ...