Tools

Progressive Suspension - FOL-2 - Fork Oil Tool - Adjuster - KitFeaturesCombination fork oil measurer and adjuster all in oneEasy to read calibration marks and sliding markerDesigned for the professional or home mechanicMakes accurate fluid level...

Progressive Suspension - FOL-1 - Oil Level Adjustment Kit - ForkFeaturesA rugged, accurate measuring scale to adjust fork oil heightBuilt-in memory device to eliminate guessworkProgressive Suspension Since 1982SpecsApplicationFork...

Race Tech - TFSH 20 - Shaft Holding Tool - 20-29 mmFeaturesA must for all suspension workHolds fork damping rods, cartridges, shock shaftsUnique design allows installation of dowels into the top of the vise jawsThe holding tools hang on the dowels...

S&S Cycle - 53-0013 - Oil Pump Drill JigFeaturesUsed to install S&S® oil pumps on early motor casesMade in the U.S.A.SpecsProduct NameDrill JigColor/FinishGrayApplicationCrankcase Oil PassageRiding StyleStreetUnitsEachMaterialSteelTypeInstallation

S&S Cycle - 53-0452 - Main Jet WrenchFeaturesUsed to change the main jet in S&S super carburetors that use #72 series jetsMade in the U.S.A.SpecsRiding StyleStreetProduct NameWrenchColor/FinishSilverUnitsEachTypeMain Jet DriverApplicationCarburetor

S&S Cycle - 510-0684 - Exhaust Dealer Service KitFeaturesEverything needed to perform a required exhaust system service or end cap replacementKit includes tamper-proof screws and S&S proprietary tamper-proof screw...

Race Tech - TFSC A01 - Adapter - Fork Spring Compressor - Harley-Davidson®FeaturesAdapter is recommended for disassembly of Harley-Davidson® cartridge forksSpecsApplicationForkProduct NameAdapterRiding StyleStreetUnitsEachColor/FinishSilverTypeSpring...

Race Tech - TFDH 01 - Damping Rod Holding ToolFeaturesWith a tap of a hammer, the taper wedges into the ID of most Damping Rods, late model and vintageDesigned to make spinning damper rods easier to removeSpecsApplicationDamper RodMaterialAluminumRiding...

Progressive Suspension - GP4-300 - Gauge - Air Pump - Digital - 0-300 psiFeaturesAccurate gauge and micro-adjust air bleed allow for precise air fill in shock or forksUses a flexible hose with no-loss connector for reaching air valves in tight...

Race Tech - TFBT 1010 - Bleeding Tool - ForkFeaturesKit includes adapters for 10 mm L x 1.0 mm, 12 mm L x 1.0 mm, 12 mm L x 1.25 mm and 14 mm L x 1.0 mm damping rodsEasily threads onto the damping rod to facilitate cartridge fork bleeding when changing...

Race Tech - TFCW 4549 - Fork Cap Wrench - 45/49 mmFeaturesUnique design works on multiple sizes of fork capsEmbossed Race Tech logo on handleSpecsColor/FinishZincRiding StyleAdventure Touring / Dual-SportRiding...

Race Tech - TFCH 06 - Cartridge Holding ToolFeaturesDesigned to remove and install the seal head assembly from the inner fork tubeIt allows changing fork springs without disassembling the valving stackIt is reversible and has two hex sizes for the two...

S&S Cycle - 530-0006 - Transmission Drilling FixtureFeaturesDrilling fixture used to locate holes for drilling and tapping of transmission case on touring models when installing a T-Series engine with oil line adapter kit 310-0435Kit comes complete with...

Race Tech - TFHD 1724 - Hex Axle ToolFeaturesFour sizes (17 mm, 19 mm, 22 mm and 24 mm)Fits many sport and dirt bikesSpecsRiding StyleOff-RoadApplicationAxleMaterialAluminumRiding StyleAdventure Touring / Dual-SportRiding...

Race Tech - TFBT 02S - Bleeding Tool - CartridgeFeaturesKit includes adapters for 10 mm L x 1.0 mm, 12 mm L x 1.0 mm, 12 mm L x 1.25 mm and 14 mm L x 1.0 mm damping rodsEasily threads onto the damping rod to facilitate cartridge fork bleeding when...

Rivco Products - HD021 - Oil Filter Wrench - 14 FluteFeaturesFeatures 14 flutes on filter wrench end; other end features 5/8" drain plug wrench (except mini wrench)Easily gets into tight spot to loosen filter without slippingAlso fits Drag Specialties...

Ridepower - RPCIGUSBUSBCADP - Power Adapter - Cigarette Lighter - USB/USB-C - BlackFeaturesOutfitted with both USB and USB-C ports, with 3.0 charging capabilitiesConstructed with a 5/8" diameter base and a 2-1/4" tall frameCigarette lighter power adapter...

S&S Cycle - 53-0045 - Compression Release ToolFeaturesFor use with S&S Compression Release KitsEase of installation and removalNot for use on OEM headsMade in the U.S.A.SpecsProduct NameSocketColor/FinishSilverApplicationEngine CaseUnitsEachRiding...

Motion Pro - 08-0058 - Tool - Chain Breaker/Chain RivetingFeaturesVersatile enough to be used on drive chains and some cam chainsIncludes three pin sizes to fit most chains (2 mm, 3 mm, 4 mm)Investment-cast, hardened body and redesigned body boltKit...

Motion Pro - 08-0006 - Tire Levers - 11-1/2" - PairFeaturesOne end is flat and the other end is curvedHeat treated for strength and durabilityProvides excellent leverageCold forged steelSpecsRiding StyleATVTypeTireColor/FinishSilverMaterialForged...

Motion Pro - 08-0008 - Holding Tool - ClutchFeaturesHolds clutch hubs, flywheels, gears, sprockets, etc.Recommended for square tooth-style clutch hubsFeatures 8 mm spanner pinsJaws open up to 5" wideWill not work on clutch baskets with reversed inner...

Motion Pro - 08-0135 - Jumbo Chain ToolFeaturesDesigned to break roller chain up to 630 (fits all standard and O-ring chain sizes 520 to 630) and to rivet chain up to 530 (not 630)Master link side plate press kit included to press on side plates on...

Motion Pro - 08-0143 - Bleeder - Brake Line - HydraulicFeaturesUnique check valve lets fluid and air escape while preventing air from re-entering the systemUniversal tool makes bleeding brakes a one-person jobWill not bleed air from a dry...

Motion Pro - 08-0182 - Cable LuberFeaturesClamps over housing and wire allowing an aerosol can to be connectedOnce lube runs out the far end, the cable is lubricatedUsed to inject lubricant into cable housingSpecsApplicationCable HousingRiding...

Parts Unlimited - Ignition Timing TesterFeaturesWhen setting or checking point-type ignitions this tool will precisely confirm if points are open or closedA switch allows for either a light or a tone at the precise time of point closureCan also be used...

Motion Pro - 08-0153 - Side Case Puller - Harley-Davidson/BuellFeaturesIncludes bracket, puller bolt and set screwsUsed to remove the right side-case coverMade in the USADesigned to work with '70 to '99 Big Twin models excluding '99 Twin Cam’s, '95-'02...

Pingel - 62082 - Holder - Cylinder Head - 12 mm/14 mmFeaturesMount in any bench vise in any position and hold cylinder head securely in place for all types of head workShaft of the tool has a drilled hole for clean and easy wall storageMade in the U.S.A...

Parts Unlimited - Piston Pin PullerFeaturesRemoves pins from sizes 14 mm - 20 mmWon't damage piston or connecting rodSpecsUnitsEachColor/FinishSilverColor/FinishBlackRiding StyleSnowProduct NamePullerTypePiston Pin

Motion Pro - 08-0427 - Gear JammerFeaturesOriginally developed for removing and installing the primary gear on a Honda CRF450R/XLocks gears in place for easy installation and removalAllows tightening of lock nuts to proper torque settingPowerful magnet...

Motion Pro - 08-0267 - Bearing Removal Tool - Wheel - 25 mmFeaturesHeat treated for durability and long service lifeSpecsColor/FinishBlackDrive Size Metric25 mmRiding StyleStreetTypeWheelProduct NameBearing Removal ToolStyleSplit ColletMeasurement...

Motion Pro - 08-0269 - Wheel Bearing Remover - Split Collet - Metric - 10/12/15/17/20/25 mm - SetFeaturesEight-piece metric set includes large driver rod, small driver rod, and removers for 10 mm, 12 mm, 15 mm, 17 mm, 20 mm and 25 mm bearingsDependable...

Motion Pro - 08-0350 - Belt Tension GaugeFeaturesDesigned to work with all belt drive models with a 10 lb specificationGraduated scale for easy referenceNew L shaped pad fits all belt sizesCompact designReplacement Part for OEM Number(s):...

Motion Pro - 08-0220 - Wrench - Rocker Box Cover - 3/16"FeaturesDesigned to reach hard-to-get-at 3/16" hex screw on the rocker boxes of Big Twin, Sportster and Buell modelsVinyl cover offers comfort and minimizes chances of damage to finished...

Motion Pro - 08-0339 - Screw - Tappet Tool - Oil FilterFeaturesO-ring design retains the tool in wrench or socket while flange design allows downward force to be applied to toolDesigned for use with 7/16" combination wrench to allow for maximum rotation...

Motion Pro - 08-0526 - Spoke Wrenches - Ergonomic - Set 6FeaturesUse open end for quick adjustment of spoke nipples and semi-closed end for those hard to turn nipples that require more torqueSpecially designed ergonomic handle allows larger turning...

Motorsport Products - 76081 - Tire Iron - 8.5" - StraightFeaturesMulti-use lever, one end flat spoon-shaped and the other a narrow hooked shapeCome in a reusable vinyl packageSpecsLength Imperial8-1/2''UnitsEachApplicationTireRiding...

Motion Pro - 08-0529 - Mini Bleeder - Brake/Hydraulic Clutch System - 10 mmFeaturesCombines wrench and bleeder valve into one convenient, compact toolAnodized billet aluminum handle with chromoly steel bodyBleeds brake systems and hydraulic clutch...

Motion Pro - 08-0482 - Mini Bleeder - Brake/Hydraulic Clutch System - 8 mmFeaturesCombines wrench and bleeder valve into one convenient, compact toolAnodized billet aluminum handle with chromoly steel bodyBleeds brake systems and hydraulic clutch...

Motion Pro - 08-0591 - Piston Tool - Brake CaliperFeaturesUltra-low-profile design removes pistons from monoblock disc brake calipersFits pistons with a center bore size of 14 mm - 28 mmNon-marring design will not harm pistons or caliperWorks on...

Namz - NJC-990120 - Crimp Tool - Mini/"U" Barrel - UniversalFeaturesDesigned for use with JAE MX-1900 series, JST, ECM/BCM Delphi or any other small terminalPerfect for small 30 to 20-gauge terminalsFor servicing late model motorcyclesMade in...