Tools

Jims - 744 - Hardware Organizer - Top EndFeaturesSpecific stands for top end, transmission, cam chest, and primaryPart organizers for powertrain assembly, teardown and storageStands nest to save spaceMade in the U.S.A...

K&L Supply - 35-8434 - Magnetic Base - Flex ShaftFeaturesFlexible indicator mounting arm locks into place to make any job easyFeatures an easy-to-use on/off knobFor use with dial indicator gaugeSpecsApplicationDial IndicatorRiding...

K&L Supply - 35-8421 - Dial Indicator - Magnetic BaseFeaturesReads 1.0" in increments of .001"Gauge can be locked for a zero settingIncludes magnetic base stand that has an adjustable dial indicator mounting arm for a wide range of...

K&L Supply - 35-9016 - Tool Tire Bead StarterFeaturesEasy to use: Just mount tire to wheel, position bead starter, then cinch down with ratchet lever; add air until bead begins to engage, then slowly ease belt tension as more air is addedAll-in-one...

K&L Supply - 35-6770 - Dolly - Bike LiftFeaturesGives the proper leverage to pivot and shift the lift around to precisely where it's needed, whether a motorcycle is mounted on it or notIncrease the mobility of the motorcycle MC625R Air LiftSpecsRiding...

Jims - 935 - Inspection Cutter Tool - Oil FilterFeaturesUse to inspect oil filter for any damaging particles that may be trapped in filterLocks down filter for a clean cut around filter baseFits filters up to 5-1/2" diameterMade in the U.S.A...

Jims - 5504 - Tappet Position HolderFeaturesTappet locations are clearly referenced on the tool, which also serves to protect the tappets from damage when removed from the engineSafely stores anti-rotation pins and tappets for proper and accurate...

Feuling Parts - 9008 - Reamer Tool - Camplate/Oil Pump - Twin Cam/M8FeaturesTo use, lightly machine (clean) the camplate relief valve seat and re-seat the plunger valveBest used in conjunction with Feuling pressure test tool part# 9010 or 9006, but can...

Jims - 2240-11-4 - Adapter - Valve Guide - Insert - 7 mmFeaturesAdapters are supported by a stand that makes it easy to press valve guides in and outAdapters for working on 7 mm valve guidesMade in the U.S.A.SpecsProduct NameAdapterTypeValve Guide...

K&L Supply - 35-8621 - Stand - Wheel Truing/BalancingFeaturesWheels mount to adjustable center cones or ball bearings for trueing and static balancingAdjustable frame rails accommodate wide rims and wheelsBalances and trues all 14" to 21" motorcycle...

K&L Supply - 35-7568 - Fork Seal Driver - Harley-Davidson®FeaturesQuickly and conveniently replaces fork seals without removing inner fork tube from the T-clampSplit-seal driver as well as 35 mm, 39 mm and 41 mm seal guides are includedFor use with stock...

K&L Supply - 35-3498 - Carburetor Cleaner Wire SetFeatures14-piece wire set with spiral knurling for cleaning popular sized jets and carb body holesSpecsRiding StyleOff-RoadRiding StyleWatercraftProduct NameCleanerStyleSpiral...

Dennis Stubblefield Sales - TOOL-B - Locking Tool - Crankshaft - Harley DavidsonFeaturesEnables timing and camshaft work to be done without the crankshaft moving from the timing mark lineLocks the crankshaft through the timing mark hole on the leftMade...

Dennis Stubblefield Sales - TOOL-A - Locking Tool - Ignition Points - Harley DavidsonFeaturesLocks ignition points to advanced position during tune-ups and distributor workFits most Big Twin Classics and '70-'78 models with ignition points systemsMade in...

Did - KM500R - Chain Tool - Chain Breaker/Riveting/Press-FitFeaturesDID logoDesigned to cut chain, press fit connecting link plates, and rivet pin heads with one easy-to-use toolMay be used to cut any 520, 525, 50 (530) or 532 chainSmall compact design;...

Andrews - 212116 - Gauge Pin - Cam Drive Gear - 0.108"FeaturesUsed to measure the outside diameter of cam drive gearsMade in the USAThere are two basic differences between '90-'99 cam gear sizes and earlier years. The overall range of gear pin...

Andrews - 212105 - Gauge Pin - Cam Drive Gear 0.105"FeaturesUsed to measure the outside diameter of cam drive gearsMade in the USAThere are two basic differences between '90-'99 cam gear sizes and earlier years. The overall range of gear pin measurements...

Belt Drives Ltd. - CLT-100 - Clutch Lock Up ToolFeaturesDesigned to help properly torque the clutch basket and hub assembly to the mainshaft of the transmissionNo need to use an impact wrench that can damage the basket, hub or other componentsFor use on...

Belt Drives Ltd. - RGLT-100 - Ring Gear Lock ToolFeaturesChoose the appropriate side of the tool for kit; one side is for open belt drives up to 06 models and the smaller, reverse side is for open belt drive kits for 07-16 modelsFor use on all Belt Drive...

Barnett - 638-30-70001 - Scorpion Hub Puller Features Used most Scorpion clutches Made in the U.S.A. Specs Color/Finish Anodized Material Steel Type Clutch...

Motion Pro - 08-0548 - Nut Driver - Clutch Adjustment - Harley-DavidsonFeaturesThrough-hole allows access with hex wrench to hold clutch adjuster screw while simultaneously tightening the adjuster lock nutDeep socket allows tool to recess into clutch...

Lang Tools - 492 - Fuel Tank Lock Ring ToolFeaturesRemove and install the lock ring on fuel tanksAllows access to the fuel filter and pumpSpecsRiding StyleStreetUnitsEachMaterialAcrylonitrile Butadiene Styrene PlasticApplicationFuel...

Lang Tools - 9280 - Wrench - Crankshaft - 24-Tooth - Ratcheting - Big TwinFeaturesUsed for rotation of the crankshaft on all 24-spline engines and to check engine timing and parts clearanceErgonomic E-Z Grip handle allows more turning power with less...

Lang Tools - 6531 - Wrench - Lower Rocker Box - Ratcheting - 1-1/4" Socket Length - EvolutionFeaturesVinyl grip provides a comfortable, ergonomic grip and prevents the wrench from scratching or marring the bikeExtra-long reversible ratcheting wrench is...

Lang Tools - 6530 - Wrench - Lower Rocker Box - Ratcheting - 1" Socket Length - Twin CamFeaturesVinyl grip provides a comfortable, ergonomic grip and prevents the wrench from scratching or marring the bikeExtra-long reversible ratcheting wrench is used...

Lang Tools - 6562 - Wrench - Rear Fender - FLFeaturesExtra long rocker box wrench with T40 bit used to remove/replace the bolt that holds the rear fender to the frame on H-D touring modelsRemoves the rear fender bolt without having to remove the tireMade...

Lang Tools - 6538 - Wrench - Exhaust BracketFeaturesLow-profile design allows for easy access to the exhaust bracket in between the frame and engineVinyl grip protects bike from damage during use and provides an ergonomic gripTo remove and install the...

Lang Tools - 444 - Steering Stem - Harley-DavidsonFeaturesImproved design and triple prong engagement allows for precise neck bearing adjustmentUsed to adjust the preload of the neck bearing on Springer forksThis is the only tool on the market to do this...

Jims - 1726-3 - Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with...

Jims - 1726-2 - Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with...

Jims - 1726-1 - Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with...

Jims - 1163 - Ball Shaft Retention PinsFeaturesLock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheelUse to secure balancers when servicing the flywheel assemblyMade in the U.S.A...

Jims - 2280 - Cam Bearing Alignment ToolFeaturesUse to check the alignment of cam bearing to cam cover bushing to within .0003" of centerlineBinding of tool indicates misalignment of cam cover and bushingMade in the U.S.A.SpecsApplicationCam...

Jims - 1148 - Rod Alignment Tool - Twin CamFeaturesUse to check rod straightness without removing the rods from the casesMade in the U.S.A.SpecsOverall Length Imperial4-1/2''Riding StyleStreetProduct NameAlignment ToolUnitsEachStyleRodApplicationEngine...

Jims - 94804-57 - Rocker Bush Remover - Twin CamFeaturesUse to ream rocker bushings to a factory fit of .0007” - .0012” in line with each otherThis precise line reamer is capable of a 24 finish or betterMade in the U.S.A.SpecsProduct NameBushing...

Jims - 764 - Plug Kit - Engine/Transmission - Twin CamFeaturesKit includes enough pieces for one Twin Cam engine and transmissionPlugs holes on engines and transmissions when rebuildingHelps seal out dirt, dust and moreMade in the U.S.A.SpecsMeasurement...

Jims - 950 - Axle Plug - HollowFeaturesLube the o-ring ends of these tools and insert in left and right ends of axleHelps establish a center point during alignmentPlug into left and right ends of axleMade in the U.S.A.SpecsColor/FinishAnodizedRiding...

Feuling Parts - 9010 - Camplate Tool - PSI Relief Valve - Twin CamFeaturesAllows the engine builder to know what psi the relief valve opens; the spring tension can be adjusted to achieve the desired pop off psiTool includes:Air regulator0-100 psi...

Jims - 2267 - Vise Stand - Cruise DriveFeaturesAligns transmission gears and shafts for installationProtects parts from damage during installationAllows for quicker, safer and easier assemblyMade in the USASpecsColor/FinishBlackRiding...

Jims - 1133 - Reamer Valve Guide Tool - 7 mmFeaturesFor 7 mm valve guides Harley-Davidson® No. 16461-02 that are used in conjunction with the latest conical (Beehive) valve springsWill also work on equivalent aftermarket 7 mm valve guidesQuality pilot...