Tools

V-Twin - 16-1070 - Rider Tool Kit for 2017 FLTDescriptionDIY Touring tool kit for 2017 FLT models. Kit includes rider tools and service tools for the rider-mechanic.This DIY tool kit will help the rider perform many general maintenence tasks for 2017 FLT...

V-Twin - 16-1063 - Rod Alignment Plate ParkerizedDescriptionRod alignment plate features a cast iron construction with a parkerized finish, for Big Twin engines. Fits:FL 1941-1985EL 1936-1952Additional Information UOM1 - EA ManufacturerMotorshop ...

V-Twin - 16-1055 - OE Crankshaft Locking Tool for XLDescriptionOE crankshaft locking tool fits 1991-1999 XL models by engaging the pinion shaft splines. This allows removal and torquing of the pinion nut during installation Fits:XL 1991-1999Additional...

V-Twin - 16-1052 - Top End Pushrod Compressor ToolDescriptionTool pushes against the top rocker box to allow one hand operation and is for use on 1936-1998 Big Twin and 1957-2003 XL models. Fits:FXR 1982-1994FXD 1991-2017FX 1971-1984EL 1936-1940FL...

V-Twin - 16-1051 - Jims TC-88 Connecting Bushing ToolDescriptionTo remove and replace wrist pin bushing without removing connecting rods from crankcase, use the Jims TC-88 connector rod bushing tool. Fits:FLT 1999-UPFLST 1999-2017FXST 1999-2017FXD...

V-Twin - 16-1047 - Flute Tap Tool 3/8 inch-18 Bright ColbaltDescriptionFlute tap tool 3/8"-18 NPT thread features 4 flutes with a bright cobalt finish. Fits:Custom applicationAdditional Information UOM1 - EA MeasurementsAdditional InformationOverall...

V-Twin - 16-1046 - Flute Tap Tool 1/8 inch-27 Bright ColbaltDescriptionFlute tap tool 1/8"-27 NPT thread features 5 flutes with a bright cobalt finish. Fits:Custom applicationAdditional Information UOM1 - EA ManufacturerV-Twin OriginUSA 2025 Catalog...

V-Twin - 16-1045 - Jims Magnetic Tappet Holder Tool SetDescriptionJims magnetic tappet holder tool set holds the tappets up while changing cams, cam support plate or oil pump on all TC-88 and M8 engines.Sold as a pair. Fits:FXST 1999-UPFLST 1999-UPFLT...

V-Twin - 16-1043 - Sifton Cam Cover Bushing Remover ToolDescriptionSifton cam cover bushing remover tool will remove the cam cover bushing and will also remove cam bushing in case.This tool is sturdy, reliable and in 1 easy operation it will remove the...

V-Twin - 16-1042 - Sifton Outer Primary Cover Starter Bearing Removal ToolDescriptionSifton outer primary cover starter bearing removal tool removes 9063 Torrington needle bearing for Big Twin and XL covers.*NOTE: This tool will also remove the OEM...

V-Twin - 16-1041 - Flywheel Fixture Center ToolDescriptionFlywheel fixture center tool is for use on hand wheel.Thread pitch is 5/8"-11. Fits:FLST 2000-2017FXD 2000-2017XL 2000-UPFXST 2000-2017FLT 2000-UPAdditional Information UOM1 - EA ...

V-Twin - 16-1038 - Clutch Hub Nut Wrench KitDescriptionClutch hub nut wrench kit includes a factory style wrench and nut with a Sifton patch. Fits:EL 1936-1940Additional Information UOM1 - KIT ManufacturerMotorshop OriginImported 2025 Catalog...

V-Twin - 16-1037 - Replica Linkert Venturi Removal ToolDescriptionIncludes three interchangeable adaptors to service all carburetors to remove venturis.The 1-3/16" collar is used for M-4, ll, 16, and 18 carburetors. The 1-3/8" collar is used for M-2, 5,...

V-Twin - 16-1034 - Fork Cap Wrench ToolDescriptionFork cap nut socket wrench tool for use an 41mm fork plugs.Thin design allows for removal of fork plug without disassembling handlebars. Will remove 1-3/8" hex fork cap nut on 1/2" drive with o-ring...

V-Twin - 16-1033 - Oil Pump Relief Valve Ball Reseat Tool ParkerizedDescriptionOil pump relief valve ball reseat tool. This tool will facilitate ball burnishing of the relief valve seat on oil pumps. Fits:FXST 1984-1998UL 1937-1948FXR 1982-1994FLT...

V-Twin - 16-1032 - Flywheel Fixture Center ToolDescriptionFlywheel fixture center tool is a replacement for the wheel bearing puller/installer tool.Thread pitch is 7/8"-14. *NOTE: Attaches to the flywheel truing hand wheel. Fits:FLST 2000-2017FXD...

V-Twin - 16-1031 - Jims Tappet Position Holding ToolDescriptionJims tappet position holding tool for Twin Cam and Sportster engines. This tool allows the tappets and anti-rotation pins to be safely and accurately stored for proper reinstallation.Tappet...

V-Twin - 16-1030 - Jims Clutch Adjusting ToolDescriptionJims clutch adjusting tool for use on Big Twins 1985-up allows the mechanic to quickly and accurately tighten the clutch adjusting screw jam nut without having the screw change position.Includes...

V-Twin - 16-1029 - Jims Transmission Assembly Vise Stand ToolDescriptionJims transmission assembly vise stand tool is used to assist in the assembly of the transmission gears and shafts.This tool holds the shafts in perfect alignment while protecting...

V-Twin - 16-1028 - Jims Main Drive Gear Case Seal Installer toolDescriptionJims main drive gear case seal installer tool ensures correct alignment and installs seal to the correct depth without damaging seal. Fits:FXST 1985-2006FXD 1991-2005FLT...

V-Twin - 16-1027 - Inner Primary Cover Bearing and Seal Remover Installer ToolDescriptionThis tool safely removes and installs the inner primary bearing without damage to the new bearing.Also removes and installs inner primary and seal that the...

V-Twin - 16-1024 - Pushrod Cover Removal and Installation ToolDescriptionPushrod cover removal and installation tool fits TC-88 models. Fits:FLT 1999-UPFLST 1999-2017FXST 1999-2017FXD 1999-2017Additional Information OEM No.94086-09 UOM1 - EA ...

V-Twin - 16-1020 - Flywheel Truing HammerDescriptionThis flywheel truing hammer is a three pound lead/steel hammer that lasts longer than a lead hammer and is still soft enough so that it will not mar flywheels. Fits:All modelsAdditional Information ...

V-Twin - 16-1011 - Fork Stem Die Tool Holder OnlyDescriptionFork stem die holder tool.Order die separately. Fits:All modelsAdditional Information UOM1 - EA MeasurementsAdditional InformationInner Diameter: 50.8mm ManufacturerMotorshop OriginImported ...

V-Twin - 16-1008 - Fork Tube Plug ToolDescriptionThis Jims fork tube plug tool is used to remove and install top fork tube plugs. Eliminates possible burring of plug, caused by wrenches. Fits:FLST 1986-2017FL 1948-1984FLT 1979-UPFX 1980-1986Additional...

V-Twin - 16-1007 - Teardrop FXST Tool KitDescriptionYou can never go wrong with this tool kit. It is supplied appropriately for each year model and includes a tool bag. The entire kit fits inside teardrop shaped tool boxes for Softails. Fits:FLST...

V-Twin - 16-1003 - Spring Fork Assembly ClampDescriptionThe spring fork assembly clamp facilitates building of stock type forks by compressing upper and lower spring. Fits:UL 1937-1948WL 1936-1952EL 1936-1940FL 1941-1948Additional Information UOM1 - EA ...

V-Twin - 16-0998 - Tappet Guide and Oil Pump Alignment ToolDescriptionUse to align tappet guide to engine case and also aligns oil pump to cam plate.Sold as a pair. Fits:FLST 1999-2017 oil pumpFXST 1999-2017 oil pumpFXD 1999-2017 oil pumpFXR 1984-1994...

V-Twin - 16-0997 - Digital Tire Pressure GaugeDescriptionThis 0-150 PSI digital tire gauge is a welcomed addition to any tool kit. Gauge includes batteries. Fits:All modelsAdditional Information UOM1 - EA ManufacturerMotorshop OriginImported 2025...

V-Twin - 16-0993 - Sifton Pushrod Adjustment GaugeDescriptionSifton pushrod adjustment gauge for use on Big Twins with hydraulic lifter. Comes complete with instructions.With this gauge in place you will be able to determine that your lifters are...

V-Twin - 16-0992 - Clutch Drum Locking ToolDescriptionThis clutch drum locking tool is for removing the clutch hub and motor nuts without problems. Fits:XL 1971-1984Additional Information OEM No.97173-71 UOM1 - EA ManufacturerMotorshop OriginImported...

V-Twin - 16-0986 - Oil Pump Drill FixtureDescriptionThe oil pump drill fixture allows drilling of cases to accept late model stock or S&S oil pumps. Fits:FX 1971-1984EL 1936-1940FL 1941-1984Additional Information UOM1 - EA ManufacturerS&S Cycle ...

V-Twin - 16-0985 - Primary Plug WrenchDescriptionPrimary plug wrench Fits:XL 1971-1984Additional Information OEM No.33186 UOM1 - EA ManufacturerMotorshop OriginImported 2025 Catalog Pages927

V-Twin - 16-0982 - Bushing Reaming ToolDescriptionThis eastern bushing reaming tool is used to ream the pinion bushing in the cam cover to size.Pilots from pinion shaft case race in engine case requires case to be disassembled for proper use. Fits:FXST...

V-Twin - 16-0981 - Bushing Reaming ToolDescriptionThis eastern bushing reaming tool fits pinion bushing in cam cover. Fits:K 1954-1956XL 1957-1976WL 1937-1973Additional Information OEM No.94812-37A UOM1 - EA MeasurementsAdditional InformationReam...

V-Twin - 16-0980 - Bushing Reaming ToolDescriptionThis eastern bushing reaming tool fits pinion bushing in cam cover. Fits:XL 1977-1985Additional Information OEM No.94812-80A UOM1 - EA ManufacturerEastern OriginUSA 2025 Catalog Pages927

V-Twin - 16-0979 - Pinion Bushing ReamerDescriptionThis eastern bushing reamer fits pinion bushing in cam cover .Includes pilot bushing. Fits:FL 1941-1954Additional Information OEM No.94813-80A UOM1 - EA ManufacturerEastern OriginUSA 2025 Catalog...

V-Twin - 16-0978 - Bushing Reaming ToolDescriptionThis eastern bushing reaming tool fits pinion bushing in cam cover. Fits:FL 1955-1957Additional Information OEM No.94814-80A UOM1 - EA ManufacturerEastern OriginUSA 2025 Catalog Pages1280

V-Twin - 16-0977 - Tappet Guide Alignment ToolDescriptionThe tappet guide alignment screws are 0-150 PSI and 1/4" wide x 24 threads for after market crankcase sets.Sold as a pair Fits:Special applicationAdditional Information UOM1 - SET ...

V-Twin - 16-0976 - Piston Ring GrinderDescriptionThe piston ring grinder accurately sizes end gap on any piston ring by rotary filing. Fits:All modelsAdditional Information UOM1 - EA ManufacturerMotorshop OriginUSA 2025 Catalog Pages860