Bagger Parts
- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
Out of stock
Wild 1 - Chubby Flatline 12" Handlebars - Chrome
Wild 1 Handlebars
$314.95Wild 1 Chubby Flatline 12" Handlebars Features: 1-1/4" diameter Drilled for internal wiring Chrome Made in USA Measurements: 12" TALL 24" WIDE FLAT 0" PULL BACK 0° WRIST ANGLE$314.95 -
Out of stock
Wild 1 - Physco Street Fighter 14" Handlebars - Chrome
Wild 1 Handlebars
$342.95Wild 1 Physco Street Fighter 14" Handlebars Features: Handlebars are 25% thicker than stock Designed with fluid bends at precise angles for maximum comfort and control Pre-drilled for internal wiring Polished welds/ diamond...$342.95 -
Out of stock
Wild 1 - Physco Street Fighter 10" Handlebars - Chrome
Wild 1 Handlebars
$342.95Wild 1 Physco Street Fighter 10" Handlebars Features: Handlebars are 25% thicker than stock Designed with fluid bends at precise angles for maximum comfort and control Pre-drilled for internal wiring Polished welds/ diamond...$342.95 -
Out of stock
Jims - 8385 Compensator Nut Retainer fits '12-'13 Twin Cam & Screamin’ Eagle Models (OEM #83935-09A, 40274-08A)
Jims
$260.95Jims - 8385 Compensator Nut Retainer fits '12-'13 Twin Cam & Screamin’ Eagle Models (OEM #83935-09A, 40274-08A) Features: Lockplate secures nut into sprocket retainer Incorporated lock tab One piece sprocket retainer for strength Made in...$260.95 -
Out of stock
Jims - 986 Cruise Drive/6-Speed Main Drive Gear Bearing/Seal Installer Tool fits '07-'20 Big Twin & '06 Dyna Models
Jims
$161.95Jims - 986 Cruise Drive/6-Speed Main Drive Gear Bearing/Seal Installer Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Holds bearings and seal square to its bore, eliminating any marring Install both bearings and seal with use of a...$161.95 -
Out of stock
Jims - 989 Main Drive Gear Sprocket Locknut Wrench fits '07-'21 Big Twin & '06 Dyna Models
Jims
$264.95Jims - 989 Main Drive Gear Sprocket Locknut Wrench fits '07-'21 Big Twin & '06 Dyna Models Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the USA Inner...$264.95 -
Out of stock
Jims - Shifter Shaft Removal Tool fits '07-'20 Big Twin & '06 Dyna Models
Jims
$34.95Jims - Shifter Shaft Removal Tool fits '07-'20 Big Twin & '06 Dyna Models Features: Loosens and removes both shifter shafts from transmission door, allowing further disassembly of transmission Made in the...$34.95 -
Out of stock
Jims - 739 5 & 6-Speed Cruise Drive Countershaft Bearing Remover/Installer Tool
Jims
$340.95Jims - 739 5 & 6-Speed Cruise Drive Countershaft Bearing Remover/Installer Tool Features: Install or remove the closed-end countershaft bearing on all 5-speed or 6-speed transmissions without using a press or tapping it in with a transmission...$340.95 -
Out of stock
Jims - 5517 Removal/Installation Shifter Mechanism Sleeve Tool fits '06 Dyna & '07-'20 Big Twin w/ 6-Speed Cruise Drive Transmission
Jims
$128.95Jims - 5517 Removal/Installation Shifter Mechanism Sleeve Tool fits '06 Dyna & '07-'20 Big Twin w/ 6-Speed Cruise Drive Transmission Features: A real time saver for removing and installing the shifter mechanism sleeve in cruise drive Big Twin...$128.95 -
Out of stock
Jims - 900 6-Speed Main Drive Gear and Bearing Remover/Installer fits '06-'17 Touring, '06 Dyna & '07-'17 Softail Models
Jims
$510.95Jims - 900 6-Speed Main Drive Gear and Bearing Remover/Installer fits '06-'17 Touring, '06 Dyna & '07-'17 Softail Models Features: Complete kit for servicing the main drive gear or the main bearing on the latest Harley-Davidson®...$510.95 -
Out of stock
Jims - 1672 Crankshaft Bearing Tool fits '03-'17 Twin Cam “A” and “B” Motors Models
Jims
$275.95Jims - 1672 Crankshaft Bearing Tool fits '03-'17 Twin Cam “A” and “B” Motors Models Features: Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in...$275.95 -
Out of stock
Jims - 995 Case Splitter Tool fits '07-'17 Twin Cam & '06 Dyna Models
Jims
$416.95Jims - 995 Case Splitter Tool fits '07-'17 Twin Cam & '06 Dyna Models Features: "Breaks" the case sealant by pushing apart both case halves Uses included hand thread-in pushing screw Flywheels will be pushed from the left case Bolts to primary...$416.95 -
Out of stock
Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models
Jims
$172.95Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...$172.95 -
Out of stock
Jims - 5820 Standard Rear Axle Installation Guide Tool fits '08-'21 Big Twin w/ Hollow 1” (25 mm)
Jims
$60.95Jims - 5820 Standard Rear Axle Installation Guide Tool fits '08-'21 Big Twin w/ Hollow 1” (25 mm) Features: Aligns wheel with swingarm, caliper brackets, wheel hubs and spacers Made in the USA For Big Twin models with hollow 1" (25 mm)...$60.95 -
Out of stock
Jims - 1147 Alternator Rotor Puller fits '97-'06 Big Twin Models
Jims
$175.95Jims - 1147 Alternator Rotor Puller fits '97-'06 Big Twin Models Features: A must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holes Tool protects threads on sprocket shaft...$175.95 -
Out of stock
Jims - 2240 Head Holder Guide Tool '48-'04 Big Twin, '57-'03 Sportster & Some SE CVO Twin Cam Models (5/16” Valve Guides)
Jims
$943.95Jims - 2240 Head Holder Guide Tool '48-'04 Big Twin, '57-'03 Sportster & Some SE CVO Twin Cam Models (5/16” Valve Guides) Features: Adapters are supported by a stand that makes it easy to press valve guides in and out A special guide...$943.95 -
Out of stock
Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models
Jims
$44.95Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 1989 Harley-Davidson Electra Glide Ultra...$44.95 -
Out of stock
Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models
Jims
$44.95Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...$44.95 -
Out of stock
Jims - 1034 Sprocket Shaft Holder fits '55-'99 Big Twin & '99-'06 Twin Cam (Except '06 Dyna)
Jims
$184.95Jims - 1034 Sprocket Shaft Holder fits '55-'99 Big Twin & '99-'06 Twin Cam (Except '06 Dyna) Features: Used to hold flywheel assembly in vise, with or without left case attached Made in the U.S.A...$184.95 -
Out of stock
Jims - 38515-90 Clutch Spring Compressor fits '90-'97 Big Twin & '91-'03 Sportster Models
Jims
$177.95Jims - 38515-90 Clutch Spring Compressor fits '90-'97 Big Twin & '91-'03 Sportster Models Features: For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can...$177.95 -
Out of stock
Jims - 1745 Bearing Simulator fits '70-'02 Big Twin Models
Jims
$107.95Jims - 1745 Bearing Simulator fits '70-'02 Big Twin Models Features: Designed to allow quick and easy removal and replacement of flywheel assembly in the left-side crankcase when checking rod-to-case, piston-to-flywheel or cylinder-to-flywheel...$107.95 -
Out of stock
Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models
Jims
$52.95Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...$52.95 -
Out of stock
Jims - 1709 Sprocket Shaft Bearing Tool fits '77-'02 Big Twin Models
Jims
$367.95Jims - 1709 Sprocket Shaft Bearing Tool fits '77-'02 Big Twin Models Features: Tool is used to remove the sprocket shaft Timken® bearing on late '86-'02 Big Twins with an integral sprocket shaft Does the job better than anything else on the...$367.95 -
Out of stock
Jims - 95660-85 Transmission Main Seal Driver fits '85-'06 Big Twin 5-Speed Models
Jims
$136.95Jims - 95660-85 Transmission Main Seal Driver fits '85-'06 Big Twin 5-Speed Models Features: Optional drivers used in conjunction with main shaft seal tool allow installation of seals Fitment 2002 Harley-Davidson Softail Fat Boy EFI...$136.95 -
Out of stock
Jims - 2234 Primary Drive Lock Tool fits '70-'06 Big Twin & '86-'22 Sportster Models
Jims
$73.95Jims - 2234 Primary Drive Lock Tool fits '70-'06 Big Twin & '86-'22 Sportster Models Features: Use on all primaries between front primary chain and motor sprocket Made in the U.S.A. Fitment 2016-2017 Harley-Davidson 1200 Roadster...$73.95 -
Out of stock
Jims - 2233 Tappet Oil Filter Plug Tool fits '70-'99 Big Twin Models
Jims
$46.95Jims - 2233 Tappet Oil Filter Plug Tool fits '70-'99 Big Twin Models Features: Removes oil screen without removing exhaust Used to remove the tappet oil screen plug Made in the U.S.A. Fitment 1999 Harley-Davidson Softail Night Train...$46.95 -
Out of stock
Jims - 94547-80A Sprocket Shaft Bearing Race Tool fits '69-'02 Big Twin Models
Jims
$112.95Jims - 94547-80A Sprocket Shaft Bearing Race Tool fits '69-'02 Big Twin Models Features: Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor cases Made in the U.S.A...$112.95 -
Out of stock
Jims - 39361-69 Sprocket Shaft Seal Installation Tool fits '69-'10 Big Twin & Twin Cam Models
Jims
$161.95Jims - 39361-69 Sprocket Shaft Seal Installation Tool fits '69-'10 Big Twin & Twin Cam Models Features: Designed to press oil seal over sprocket shaft into case Made in the U.S.A. Fitment 2010 Harley-Davidson Street Glide Trike...$161.95 -
Out of stock
Jims - 34643-84 Valve Seal Installer for all Evolution Valve Guide Seals (OEM #34643-84)
Jims
$82.95Jims - 34643-84 Valve Seal Installer for all Evolution Valve Guide Seals (OEM #34643-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...$82.95 -
Out of stock
Jims - 1010 Evolution Rod Alignment Tool for 0.791” Wrist Pin
Jims
$42.95Jims - 1010 Evolution Rod Alignment Tool for 0.791” Wrist Pin Features: Use to check rod straightness without removing the rods from the cases Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...$42.95 -
Out of stock
Jims - 1012-70TB Cam Bushing Installer fits '70-'99 Big Twin Models (Except Twin Cam (OEM #25581-70))
Jims
$77.95Jims - 1012-70TB Cam Bushing Installer fits '70-'99 Big Twin Models (Except Twin Cam (OEM #25581-70)) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking...$77.95 -
Out of stock
Jims - 955 Gauge for Harley-Davidson Injection Pressure fits '01-'20 Big Twin Models w/ Delphi EFI (Except '18-'20 Softails)
Jims
$638.95Jims - 955 Gauge for Harley-Davidson Injection Pressure fits '01-'20 Big Twin Models w/ Delphi EFI (Except '18-'20 Softails) Features: Includes all necessary parts to diagnose Delphi fuel injection; a large gauge assembly, 8" hose, 2" hose, fuel tank...$638.95 -
Out of stock
Jims - 1047-TP Crank Assembly Removal Tool fits '55-'06 Big Twin Models (Except '06 Dyna)
Jims
$338.95Jims - 1047-TP Crank Assembly Removal Tool fits '55-'06 Big Twin Models (Except '06 Dyna) Features: This tool can only be used for removing the flywheel from the left case Will also press cases apart and break sealant bond Some case pressing will...$338.95 -
Out of stock
Jims - 1013-54TB Pin Bushing Installer fits '54-'92 Big Twin Models (OEM #25582-54/73)
Jims
$77.95Jims - 1013-54TB Pin Bushing Installer fits '54-'92 Big Twin Models (OEM #25582-54/73) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made...$77.95 -
Out of stock
Jims - 1030-TS Crank Pin Flywheel Socket fits 'L83-'99 Big Twin Models (OEM #23969-83)
Jims
$117.95Jims - 1030-TS Crank Pin Flywheel Socket fits 'L83-'99 Big Twin Models (OEM #23969-83) Features: Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A...$117.95 -
Out of stock
Jims - 95760-TB Puller Camshaft Bearing fits '58-'99 Big Twin Models (Except Twin Cam)
Jims
$272.95Jims - 95760-TB Puller Camshaft Bearing fits '58-'99 Big Twin Models (Except Twin Cam) Features: Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with...$272.95 -
Out of stock
Jims - 95760-TP Pinion Bearing Puller fits '54-'99 Big Twin Models
Jims
$251.95Jims - 95760-TP Pinion Bearing Puller fits '54-'99 Big Twin Models Features: Use to remove pinion bushing from cam cover in one easy operation Use with JIMS® Cam Cover Holder Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...$251.95 -
Out of stock
Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna)
Jims
$77.95Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna) Features: Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain...$77.95 -
Out of stock
Drag Specialties - 3-1/4" Chrome Magnetic Ring Oil Filter With Nut fits '17-'24 M-Eight, '99-'17 Twin Cam Models (OEM #63798-99, 63731-99A)
Drag Specialties
$25.35Drag Specialties - 3-1/4" Chrome Magnetic Ring Oil Filter With Nut fits '17-'24 M-Eight, '99-'17 Twin Cam Models (OEM #63798-99, 63731-99A) Features: High-quality chrome spin-on-style oil filters Magnetic filters are designed with a magnetic ring in...$25.35 -
Out of stock
Drag Specialties - Oil Filter with Nut fits '17-'24 M-Eight (Standard Capacity), '99-'17 Twin Cam Models (OEM #63731-99A, 63798-99)
Drag Specialties
$19.33 - $22.39Drag Specialties - Oil Filter with Nut fits '17-'24 M-Eight (Standard Capacity), '99-'17 Twin Cam Models (OEM #63731-99A, 63798-99) Features: High-quality spin-on filters are a dependable replacement for most Harley-Davidson models Includes a 17 mm...$19.33 - $22.39
Harley Bagger Parts
Upgrade your ride with top-quality Harley Bagger parts built for style, performance, and long-haul reliability. Whether you're customizing a Road Glide, Street Glide, Road King, Electra Glide, or any other Touring model, our collection of Performance Bagger parts is ready to help you fine-tune every detail.
From suspension and exhaust upgrades to lighting, foot controls, and touring essentials — we stock the gear serious riders trust to push farther and ride harder. Whether you're building a show-stopping custom or dialing in comfort for long-distance rides, these Harley Bagger parts deliver the fit and function your bike deserves.
Don’t settle for stock. Explore our full lineup of performance Harley Bagger parts and take your Touring build to the next level.