Bagger Parts

Jims - 1707 Cleveblock Spreading Tool fits '80-'01 5-Speed Rubber-Mount Frames Features: Spreads the swing arm cleveblocs allowing for installation of the swing arm Use to install the swing arm in a 5-Speed rubber mount frame Comes with...

Jims - 34734-80 Main Drive Gear Bearing/Seal Installer Tool fits '80-'90 5-Speed Big Twin Models Features: Holds bearings and seal square to its bore, eliminating any marring Install both bearings and seal with use of a one-ton press Install...

Jims - 34623-83 Piston Pin Tool fits '84-'99 Big Twin (Except Twin Cam), '86-'03 Sportster Models Features: This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention...

Jims - 1010 Evolution Rod Alignment Tool for 0.791” Wrist Pin Features: Use to check rod straightness without removing the rods from the cases Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 94805-57 Pinion Bushing Line Reamer fits '54-'99 Big Twin Models (Except Twin Cam) Features: Use on all Big Twin '54-'99 single cam only, (NOTE: Includes aftermarket motors, also XL '57 to early '84 idler gear bushing) Designed to line-ream...

Jims - 1041-TC Camshaft Cover Holder Tool fits '70-'99 Big Twin Models (Except Twin Cam) Features: Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings Clamps in vice or Bridgeport™ mill Made in the U...

Jims - 95970-32C Piston Pin Bush Tool fits '36-'99 Big Twin, '57-'20 Sportster & Buell Models (Except 1125R) Features: Use to remove and install wrist pin bushings without removing rods from crankcase Made in the U.S.A...

Jims - 1280 Camshaft Bearing Puller fits '99-'06 Twin Cam (Except '06 Dyna) for Removal of Bearings, 'L00-'06 FXST/FL & 'L00-'05 FXD for Removal of Front Cam Bearing Features: Once the camshafts are removed from the support plate this tool will...

Jims - 1275 Crankshaft Bearing Tool fits '99-'02 Twin Cam “A” Motors Features: Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A...

Jims - 74420-94 Electronic Speedometer Sensor fits '99-'03 FLT Model (OEM #74420-94, 74429-97, 74429-97A) Features: Top-quality replacement sensor Also works on any aftermarket transmission case with a speedometer sensor hole Includes O-ring,...

Jims - 955 Gauge for Harley-Davidson Injection Pressure fits '01-'20 Big Twin Models w/ Delphi EFI (Except '18-'20 Softails) Features: Includes all necessary parts to diagnose Delphi fuel injection; a large gauge assembly, 8" hose, 2" hose, fuel tank...

Jims - 954 Pump Ring Tool fits '08-'20 FLHT Model Features: Use for quick and easy service of fuel filter and other fuel-related parts Removes/installs retaining ring holding fuel pump Heavy-duty construction Made in the U.S.A...

Jims - 970 3rd Hand Axle Locker Tool fits '02-'21 FLT/​FLHT Models Features: Eliminates the need for a helper or trying to blindly hold the axle from the other side of the tire Prevents axle from moving while torquing down the axle nut after setting...

Jims - 977 Fork Stem Nut Wrench fits '96-'13 FLHT & '94-'13 FLHR Models Features: This tool allows the ability to loosen, tighten and torque to spec the 1-1/2” stem nut without radio removal Normally to get access to the top stem nut...

Jims - 5827 Fork Cap Allen Socket fits '14-'20 Touring Models Features: Harley-Davidson® recently updated the fork cap on touring bikes, and you now need a large Allen head socket for disassembly Works on touring models with 49 mm forks Made in...

Jims - 5515 Neck Bearing Tool fits '14-'20 Touring & H-D FL Trike Models Features: Tool has tapered drivers that ensure the correct installed alignment and depth of steering stem races Eliminates the risk of damaging the races and bearings...

Jims - 2232 Bearing Race Tool fits '84-'17 Big Twin (Except '14-'17 Dressers), '86-'22 Sportster & '94-'02 Buell OEM Frames (Will Also Work on Most Aftermarket Frames) Features: Removes and installs steering head bearing race on 84-16 Big Twin...

Jims - 96600-36B Valve Spring Compressor Tool fits '36-'04 Big Twin & '57-'03 Sportster Models Features: Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end...

Jims - 97225-55 Sprocket Shift Bearing Installation Tool fits '55-'02 Big Twin Models Features: Used on '84-'02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearing Made in the U.S.A...

Jims - 1743 Swingarm Bushing Tool fits '80-'01 FLT/​FLHT, '82-'99 FXR & all Aftermarket FXR-Style Frames Features: Allows installation of delicate, silicone cleveblock bushings in swingarm without damage Tool presses on outer sleeve of...

Jims - 1030-TS Crank Pin Flywheel Socket fits 'L83-'99 Big Twin Models (OEM #23969-83) Features: Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A...

Jims - 33071-73 Bearing Race Remover and Installer fits '73-'99 Big Twin, Sportster & Buell Wheels Features: Designed to remove and install bearing cups in cast wheels Use with JIMS® Handle Fitment 1999 Harley-Davidson Super...

Jims - 94660-37A Counter Shaft Sprocket Locknut Wrench fits '36-'06 Big Twin Models (Except '06 Dyna) Features: Removes hex nut from end of main drive gear that secures the rear drive transmission pulley Extra-long two-piece design Made in the...

Jims - 95760-TB Puller Camshaft Bearing fits '58-'99 Big Twin Models (Except Twin Cam) Features: Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with...

Jims - 95960-52C Clutch Hub Puller fits '36-'90 Big Twin Models Features: Used to remove wet and dry clutch hubs without removing clutch release rod 4 bolts included for dry clutch removal Made in the U.S.A...

Jims - 1051 Wrist Pin Bushing Tool fits '99-'06 Twin Cam Models Features: Used to remove and install wrist pin bushings without removing connecting rods from crankcases Comes with instructions Made in the U.S.A...

Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna) Features: Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain...

LA Choppers - Pinned Hefty Top Clamp fits '99-'23 Big Twin Models w/ 3-1/2 ” on Center Risers & Offset Mounting Holes Features: Fits Hefty handlebars and risers Polished aluminum construction Pinned to prevent movement of handlebars Made...

Custom Cycle Engineering - Steering Damper System fits '99-'07 FLHR/​FLHT/​FLHTCU/​FLHX Models Features: This complete steering damper system stabilizes the front fork and helps prevent front-end wobble Custom-designed 1-1/4" clamp and bracket...

Custom Cycle Engineering - Swingarm Retrofit Kit fits '99-'01 FLT/​FLHT/​FLHR Models Features: Retrofits the improved swingarm from 02-08 Touring models to a 84-01 Touring models No need to alter transmission housing Will require the purchase of a...

Custom Cycle Engineering - Swingarm Retrofit Kit w/ Pivot Shaft fits '99-'01 FLT/​FLHT/​FLHR Models Features: Retrofits the improved swingarm from 02-08 Touring models to a 84-01 Touring models No need to alter transmission housing Will require the...

Custom Cycle Engineering - Engine Equator II fits '09-'16 Touring Models Features: Allows all Dresser riders to correct chassis misalignment, which is impossible to achieve with the stock motor mount Billet aluminum bracket replaces the forged front...

Arlen Ness - Stage 1 Big Sucker Air Cleaner Kit fits '93-'99 Evolution Big Twin Models Features: Kits include backing plate, filter, breather bolts, steel cover and necessary hardware Billet aluminum or steel outer cover, available in black or chrome...

This front suspension cartridge kit is available in two different spring rates, Performance or Comfort. The Performance kit is designed with a stiffer spring rate. This characteristic is ideal for aggressive riding, providing a more responsive and firm...

Uni Filter - Air Filter Element fits '86-'89 80” Evolution Big Twin Models (OEM #29259-86) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still providing superior filtration Made in the...

Uni Filter - Air Filter Element fits '84-'85 80” Evolution Big Twin Models (Except FLT, FLHT (OEM #29259-83A)) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still providing superior...

Uni Filter - Air Filter fits '80-'82 FLT, '82-'83 FXR, 'L78-'82 Sportster 1000, 'L78-'84 FX, FL & FLH Models (OEM #29255-78) Features: Constructed of a unique, open-cell polyurethane material that allows maximum airflow while still providing...

Drag Specialties - Oil Filter fits '17-'24 M-Eight (Standard Capacity), '99-'17 Twin Cam Models (OEM #63731-99A, 63798-99) Features: High-quality spin-on filters are a dependable replacement Fitment 2024 Harley-Davidson Road King Police...

Drag Specialties - 3-1/4" Chrome Magnetic Ring Oil Filter fits '86-'22 Sportster (Except RH Sportster), '09-'12 XR1200/X Models (OEM #63806-83, 63796-77A, 63805-80A) Features: High-quality chrome spin-on-style oil filters Magnetic filters are...

Drag Specialties - Oil Filter fits '86-'22 Sportster (Except RH Sportster), '09-'12 XR1200/X Models (OEM #63806-83, 63796-77A, 63805-80A) Features: High-quality spin-on filters are a dependable...