Softail Engine

Jims - 995 Case Splitter Tool fits '07-'17 Twin Cam & '06 Dyna Models Features: "Breaks" the case sealant by pushing apart both case halves Uses included hand thread-in pushing screw Flywheels will be pushed from the left case Bolts to primary...

Jims - 988 Valve Spring Compressor fits '05-'17 Twin Cam (Except SE Models), '04-'22 Sportster (Except RH Sportster) & Buell Models (Except 1125R) Features: Used to remove and replace valve and new-style conical valve spring Requires use of JIMS...

Jims - 975 Engine Rotator Tool fits '07-'17 Twin Cam & '06 Dyna Glide Models Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 976 Engine Rotator Tool fits '55-'06 Big Twin Models (Except '06 Dyna Glide) Features: Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims - 956 Replacement Sleeve Timken Case Bearing Tool Features: Sleeve is several times stronger than stock aluminum case material that standard bearings ride in Replacement sleeve kit for Timken® Case Bearing Tool Made in the...

Jims - 937 7mm Valve Guide Remover fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125R) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made...

Jims - 5829 Cylinder Torque Plates fits '17-'20 M-Eight 107”, 114” Models Features: Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U...

Jims - 95660-77 4-Speed Seal Driver fits '82-'86 Big Twin Models Features: Optional drivers used in conjunction with main shaft seal tool allow installation of seals Fitment 1986 Harley-Davidson Softail Heritage...

Jims - 1146 Crankshaft Bearing Installer fits '00-'17 Twin Cam “B” Motors Models Features: Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A...

Jims - 1167 Balancer Shaft/Removal Bearing Tool fits '00-'06 Twin Cam “B” Motors Models Features: Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the...

Jims - 1110 0.105" Camshaft Pinon Gauge Pins fits '54-'89 Big Twin Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 1989 Harley-Davidson Electra Glide Ultra...

Jims - 1111 0.108" Camshaft Pinion Gauge Pins fits '90-'99 Big Twin Evolution Models Features: Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 33443-84 Tappet Aligning Tool fits 'L76-'17 Big Twin Models (Except M-Eight) Features: Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment...

Jims - 1288 Crankshaft Guide fits '99-'17 Twin Cam & '03-'09 Buell XB9R/X B9S Models Features: Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A...

Jims - 34623-83 Piston Pin Tool fits '84-'99 Big Twin (Except Twin Cam), '86-'03 Sportster Models Features: This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention...

Jims - 34643-84 Valve Seal Installer for all Evolution Valve Guide Seals (OEM #34643-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...

Jims - 94805-57 Pinion Bushing Line Reamer fits '54-'99 Big Twin Models (Except Twin Cam) Features: Use on all Big Twin '54-'99 single cam only, (NOTE: Includes aftermarket motors, also XL '57 to early '84 idler gear bushing) Designed to line-ream...

Jims - 1041-TC Camshaft Cover Holder Tool fits '70-'99 Big Twin Models (Except Twin Cam) Features: Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings Clamps in vice or Bridgeport™ mill Made in the U...

Jims - 95970-32C Piston Pin Bush Tool fits '36-'99 Big Twin, '57-'20 Sportster & Buell Models (Except 1125R) Features: Use to remove and install wrist pin bushings without removing rods from crankcase Made in the U.S.A...

Jims - 96600-36B Valve Spring Compressor Tool fits '36-'04 Big Twin & '57-'03 Sportster Models Features: Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end...

Jims - 1047-TP Crank Assembly Removal Tool fits '55-'06 Big Twin Models (Except '06 Dyna) Features: This tool can only be used for removing the flywheel from the left case Will also press cases apart and break sealant bond Some case pressing will...

Jims - 1283 Camshaft Chain Tensioner Tool fits '99-'06 Twin Cam Models (Except '06 Dyna) Features: Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain...

Jims - 1672 Crankshaft Bearing Tool fits '03-'17 Twin Cam “A” and “B” Motors Models Features: Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in...

Jims - 938 7mm Valve Guide Installer fits '05-'17 Twin Cam, '04-'20 Sportster & '04-'09 Buell Models (Except 1125CR) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve...

Jims - 2240 Head Holder Guide Tool '48-'04 Big Twin, '57-'03 Sportster & Some SE CVO Twin Cam Models (5/16” Valve Guides) Features: Adapters are supported by a stand that makes it easy to press valve guides in and out A special guide...

Jims - 1034 Sprocket Shaft Holder fits '55-'99 Big Twin & '99-'06 Twin Cam (Except '06 Dyna) Features: Used to hold flywheel assembly in vise, with or without left case attached Made in the U.S.A...

Jims - 2233 Tappet Oil Filter Plug Tool fits '70-'99 Big Twin Models Features: Removes oil screen without removing exhaust Used to remove the tappet oil screen plug Made in the U.S.A. Fitment 1999 Harley-Davidson Softail Night Train...

Jims - 1010 Evolution Rod Alignment Tool for 0.791” Wrist Pin Features: Use to check rod straightness without removing the rods from the cases Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...

Jims - 1012-70TB Cam Bushing Installer fits '70-'99 Big Twin Models (Except Twin Cam (OEM #25581-70)) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking...

Jims - 34731-84 Valve Guide Installer fits all Evolution & '99-'04 Twin Cam Models (OEM #34731-84) Features: Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A...

Jims - 1013-54TB Pin Bushing Installer fits '54-'92 Big Twin Models (OEM #25582-54/73) Features: Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made...

Jims - 1030-TS Crank Pin Flywheel Socket fits 'L83-'99 Big Twin Models (OEM #23969-83) Features: Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A...

Jims - 95760-TB Puller Camshaft Bearing fits '58-'99 Big Twin Models (Except Twin Cam) Features: Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with...

Jims - 95760-TP Pinion Bearing Puller fits '54-'99 Big Twin Models Features: Use to remove pinion bushing from cam cover in one easy operation Use with JIMS® Cam Cover Holder Made in the U.S.A. Fitment 2000 Harley-Davidson FXR...