Jims Tools

Jims Tools - Primary Locking Bar for 5-Speed FXR/FLT/FLHT Models  This bar is to be used to lock primary for service work. Features Immobilizes primary drive Allows for tightening with a...

Jims Tools - Primary Locking Bar for '85-'06 Softails, '91-'05 Dyna Glide & 4-Speed Big Twin Models  This bar is to be used to lock primary for service work. Features Immobilizes...

Jims Tools - Primary Locking Bar for '91-'08 XL883 and '94-'02 Buell Models  This bar is to be used to lock primary for service work. Features Immobilizes primary drive Allows for tightening...

Jims Tools - Primary Locking Bar for '06-'17 Dyna and '07-'17 Softail Models  This bar is to be used to lock primary for service work. Features Immobilizes primary drive Allows for tightening...

Jims Tools - Primary Locking Bar for '07-'16 Touring Models  This bar is to be used to lock primary for service work. Features Immobilizes primary drive Allows for tightening with a torque...

Jims Tools - Primary Locking Bar for '04-'20 XL1200 Models  This bar is to be used to lock primary for service work. Features Immobilizes primary drive Allows for tightening with a torque...

Jims Tools M8 Softail Coil Relocation Kit fits '18-'20 Softail Models The M8 Softail Coil Relocation Kit is especially designed for the bike builder. The kit only calls for a little grinding and...

Jims Pinion Gear Puller This tool is used to remove the pinion gear. May also be used to install pinion gear. Features: Collar included Made in USA Fitment: '32-'92 EL, FL, FLH '84-'92...

Jims Gear Shaft Nut Socket Wrench This tools special socket makes removal and installation of special gear shaft nut easy. Features: Made in USA Fitment: '54-'92 FLH '86-'92 FLST '71-'86...

Jims Pinion Gear Locking Tool This tool is used to lock pinion gear, necessary to torque the pinion nut. Features: Simple to use, align underneath gear and screw into case Use P/N 496082 tool...

Jims Cam Seal Installer and Remover This tool removes and installs cam seal without removing the cam cover. Simple to use, just mount tool in cover, screw in the two removing screws, turn center and...

Jims Wheel Bearing Race Removal Tool Handle The perfect fit for your needs. Features: 12" Long

Jims Cam Bearing Tool This tool is used to install inner cam bearing. It has to be used with P/N 491803 handle.   Features: Made in USA Fitment: '58-'98 FLH '84-'99 FXST '86-'99...

Jims Inner Cam Bearing Installation Tool This tool easily presses the inner cam bearing smoothly into the right case with the cases assembled to the proper depth. Features: Use P/N 496138 to...

Jims Cam Assembly Tool This tool holds both cams in an upright position while lowering the cam support plate over both guides and cam journal guides. Features: Manufactured from non-marring...

Jims Camshaft Remover and Installer This tool will remove and replace front and rear camshafts and ball bearings. It provides the precision alignment of the camshaft to insure a smooth press in and...

Jims Inner Cam Bearing Installer Tool This tool presses in the two inner cam bearings. Designed to press from letter side of the inner cam bearings by putting all the pushing pressure to the very...

Jims Inner Cam Bearing Remover Tool This tool removes the inner cam bearing. It keeps all pin bearings from falling into the engine case. Features: Made in USA Fitment: '07-'17 Big...

Jims Cam/Crank Sprocket Lock Tool This tool is used to lock the camshaft and crankshaft sprockets to properly remove or replace and torque the sprocket bolts. Features: Made from non-marring...

Jims - Connecting Rod Bushing Tool fits '36-'99 Big Twin Models (All Single Cam Models) The Connecting Rod Bushing Tool by Jims Tools is used to remove and replace wrist pin bushings, without having...

Jims Piston Support Plate This tool is used to help install the rings and cylinder over the piston by providing a non-marring flat support to push the bottom of the piston against...

Jims - Wrist Pin Remover fits '99-'06 FLH, '00-'06 FXST/FLST & '99-'05 FXD Models The Wrist Pin Remover by JIMS Tools can easily be used by one person. There is no need for another technician to...

Jims - Oxygen (O2) Sensor Wrench This tool is used to remove or install Harley Davidson four-wire heated oxygen sensors. Features: The new fragile O2 sensor must be torqued to 14 ft./lbs.,...

Jims Rocker Box Alignment Screws These alignment screws will ensure that the rocker cover alignment is right on. Misalignment can compromise the sealing surface and looks bad. They can also cause...

No longer do you need to fight trying to install this fragile exhaust seal Never worry about an exhaust leak again Use on 84'-15' Evolution Big Twin, XL, all twin cam models

So the dipstick on your smoking hot bike is way to hot to check your oil, heres an easy way to remove it. Allows riders and mechanics to quickly and safely remove the engine oil level dipstick...